Breaking News
Content tagged with Microprocessor
posted in March 2002
PDA chip content to 'inch up' in 2002, says report
News & Analysis  
3/26/2002   Post a comment
EL SEGUNDO, Calif. -- Unit shipments of personal digital assistants (PDAs), also known handheld computers, are expected to grow from 12.1 million systems in 2001 to about 50 million units in 2006, according to a new report from iSuppli Corp.
Intel's server 'blueprints' program for MPUs attracts over 30 companies
News & Analysis  
3/25/2002   Post a comment
SANTA CLARA, Calif.--Intel Corp. today announced it has lined up more than 30 systems integrators, software houses, and computer suppliers to use and support server platforms based on its microprocessors--such as the Xeon series and the upcoming McKinley processors.
Early indicators show 'uneven' bounce from downturn's bottom, says report
News & Analysis  
3/20/2002   Post a comment
SCOTTSDALE, Ariz. -- The integrated circuit business is now staging an apparent recovery, but the initial steps in the bounce-back are extremely uneven in IC markets when revenues are broken down into major product segments, observed IC Insights Inc. in its new March newsletter released this week.
Intel has dual processor Pentium III Tualatin
News & Analysis  
3/19/2002   Post a comment
Intel Corp. on Tuesday unveiled its first dual processor Pentium III Tualatin 800MHz blade server chips, its highest- performance chip yet for the ultra-dense low power servers.
No new CTO for ARC, more emphasis on software
News & Analysis  
3/15/2002   Post a comment
UK cores group will not replace Keith Diefendorff following his move to rival MIPS Technologies.
AMD claims desktop PC processor share grew to 22% in 2001
News & Analysis  
3/14/2002   Post a comment
SUNNYVALE, Calif.--Declaring an uphill victory over archrival Intel Corp., executives at Advanced Micro Devices Inc. today cited new market share estimates from Dataquest Inc. that show AMD gaining ground in several desktop computer segments on its much bigger competitor in PC processors.
Intel says 'Foster' processors beat RISC chips from IBM, Sun and MIPS
News & Analysis  
3/12/2002   Post a comment
HANNOVER, Germany -- During the CeBIT 2002 trade show here today, Intel Corp. expanded its efforts in the high-end, 32-bit server market, announcing the first in a family of Pentium 4-based microprocessors for this segment.
Intel sees some strength in server demand, fab cost savings in Q1
News & Analysis  
3/7/2002   Post a comment
SANTA CLARA, Calif.--Intel Corp. today said it expects first quarter revenues to be in a range of $6.6-to-$6.9 billion as compared to a previous estimate of $6.4-to-$7.0 billion.


Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Radio
LATEST ARCHIVED BROADCAST

What are the engineering and design challenges in creating successful IoT devices? These devices are usually small, resource-constrained electronics designed to sense, collect, send, and/or interpret data. Some of the devices need to be smart enough to act upon data in real time, 24/7. Specifically the guests will discuss sensors, security, and lessons from IoT deployments.

Brought to you by:

Most Recent Comments
michigan0
 
SteveHarris0
 
realjjj
 
SteveHarris0
 
SteveHarris0
 
VicVat
 
Les_Slater
 
SSDWEM
 
witeken
Most Recent Messages
9/25/2016
4:48:30 PM
michigan0 Sang Kim First, 28nm bulk is in volume manufacturing for several years by the major semiconductor companies but not 28nm FDSOI today yet. Why not? Simply because unlike 28nm bulk the LDD(Lightly Doped Drain) to minimize hot carrier generation can't be implemented in 28nm FDSOI. Furthermore, hot carrier reliability becomes worse with scaling, That is the major reason why 28nm FDSOI is not manufacturable today and will not be. Second, how can you suppress the leakage currents from such ultra short 7nm due to the short channel effects? How thin SOI thickness is required to prevent punch-through of un-dopped 7nm FDSOI? Possibly less than 4nm. Depositing such an ultra thin film less then 4nm filum uniformly and reliably over 12" wafers at the manufacturing line is extremely difficult or not even manufacturable. If not manufacturable, the 7nm FDSOI debate is over!Third, what happens when hot carriers are generated near the drain at normal operation of 7nm FDSOI? Electrons go to the positively biased drain with no harm but where the holes to go? The holes can't go to the substrate because of the thin BOX layer. Some holes may become trapped at the BOX layer causing Vt shift. However, the vast majority of holes drift through the the un-dopped SOI channel toward the N+Source,...
Like Us on Facebook
Special Video Section
Once the base layer of a design has been taped out, making ...
In this short video we show an LED light demo to ...
The LTC2380-24 is a versatile 24-bit SAR ADC that combines ...
In this short video we show an LED light demo to ...
02:46
Wireless Power enables applications where it is difficult ...
07:41
LEDs are being used in current luxury model automotive ...
With design sizes expected to increase by 5X through 2020, ...
01:48
Linear Technology’s LT8330 and LT8331, two Low Quiescent ...
The quality and reliability of Mill-Max's two-piece ...
LED lighting is an important feature in today’s and future ...
05:27
The LT8602 has two high voltage buck regulators with an ...
05:18
Silego Technology’s highly versatile Mixed-signal GreenPAK ...
The quality and reliability of Mill-Max's two-piece ...
01:34
Why the multicopter? It has every thing in it. 58 of ...
Security is important in all parts of the IoT chain, ...
Infineon explains their philosophy and why the multicopter ...
The LTC4282 Hot SwapTM controller allows a board to be ...
This video highlights the Zynq® UltraScale+™ MPSoC, and sho...
Homeowners may soon be able to store the energy generated ...
The LTC®6363 is a low power, low noise, fully differential ...