ESD devices save space in high-speed, high frequency apps Product News 12/31/2003 Post a comment A new series of electrostatic discharge (ESD) protection diodes from Royal Philips Electronics protect consumer and communications applications from ESD and other voltage induced transient pulses, and saves up to 90% board space in high speed, high frequency applications.
Band interleaving paves way for 802.11a News & Analysis 12/31/2003 Post a comment The number of wireless-LAN users is growing exponentially. But with the majority of this equipment operating in the 2.4-GHz band with only three clear channels, as per 802.11b (11 Mbits/second) and 802.11g (54 Mbits/s),
Designing high-density voice-capable WLANs News & Analysis 12/31/2003 Post a comment The territory for large-scale enterprise wireless LANs is mostly uncharted, yet many are now looking at how to build a standards-based, enterprise-grade WLAN for both voice and high-user-density data.
802.11n: Defining a high-throughput WLAN News & Analysis 12/31/2003 Post a comment At the January IEEE 802.11 interim meeting in Vancouver, British Columbia, Jan. 12-15, Task Group "n" is expected to issue a call for proposals for the high-throughput amendment to the 802.11 standard.
Wireless eyes throughput challenge News & Analysis 12/31/2003 Post a comment The proliferation of wireless networking in the office, at home and in public spaces has generated considerable interest in the technology's potential for serving an ever-expanding list of applications.
MIMO answers high-rate WLAN call News & Analysis 12/31/2003 Post a comment Wireless-LAN technology is not keeping up with the demands of home video networks, interactive gaming, voice-over-Internet Protocol, transportation system access and last-mile data distribution.
Transformers designed for rugged mil specs Product News 12/31/2003 Post a comment The rugged 4260-1646 and 4260-1647 Series of data bus interface transformers from Datatronics Romoland, Inc. support high-speed data transmission requirements in a wide range of mission critical industrial and military applications.
Analyst's Couch: ICs to grow 18% in '04 News & Analysis 12/31/2003 Post a comment Fueled by cellular phones, PCs and other products in the marketplace, the semiconductor business is expected to grow 18 percent in 2004 over 2003, according to International Data Corp. (IDC).
Making the Most Out of 802.3af Design How-To 12/30/2003 Post a comment New power-over-Ethernet specification allows designers to remove the power cord and powerup over Ethernet lines. Here's a look inside this new IEEE spec.
Quad regulator takes care of LCDs Product News 12/30/2003 Post a comment Linear Technology's LT1943 quad output regulator is designed specifically to power and protect 22-inch and larger thin-film transistor liquid-crystal display (TFT LCD) panels. Included in the power block (three supplies for the display as well as a 3.3- or 5-V logic supply) is a 2.6-amp boost regulator to drive the TFTs, a high voltage TFT biasing output, an inverter for negative TFT biasing, and a 2.4-amp buck regulator to power VLOGIC. All of the switchers are synchronized to an internal 1.2 M
Tactile sensors flex to all pressures Product News 12/30/2003 Post a comment Combining a sensor with signal conditioning electronics, Pressure Profile Systems, Inc.'s new C500 tactile sensor can discern the slightest pressure on curved and angular surfaces.
Single Chip Processor for DVD Recorders Product News 12/30/2003 Post a comment Murray Slovick's first take on the DMN-8602 processor for DVD recorders is that LSI Logic has come to play. Of particular note is the company's claim that the chip integrates a number of system functions resulting in a cost reduction (BOM) of up to $20 over and above LSI Logic's previous DVD recorder parts.
Active-clamp PWM controller peaks ZVS designs Product News 12/29/2003 Post a comment National Semiconductor's LM5025 is an active-clamp PWM controller for high-frequency forward converter topologies designed to boost the efficiency and power density of conventional forward regulators. Using the company's analog bipolar-CMOS-DMOS technology to cut external component count, the LM5025 integrates a 3-amp driver, 100-volt start-up bias regulator and a user programmable 1 MHz oscillator, and the chip exhibits a total propagation delay of less than 100 ns, thus suiting it to a variety
DC/DC driver IC addresses pre-biased loads Product News 12/29/2003 Post a comment Intersil's new ISL6608, for driving two n-channel power MOSFETs in synchronous-buck, multiphase power converters, features a diode-emulation mode that eases power-up into a pre-biased load and maximizes performance under light-load conditions.
Eighth-bricks tout high thermal performance Product News 12/29/2003 Post a comment Ault's HDE1-75 single-output eighth-bricks, suited to high-temperature ambient environments, deliver up to 25 amps at 1.8, 2.5, or 3.3 volts from a 36-75 VDC input. Using the company's Tronix-Flex technology, these 75-watt, 350-kHz DC/DC converters feature an FET array design that stacks MOSFETs in parallel on multi-level printed circuit boards and an integrated heat sink to achieve high power density at elevated temperatures (100 watts/in3 at 85°C) despite minimal air flow.
Sony robot runs and jumps News & Analysis 12/28/2003 Post a comment Sony Corp. has developed an integrated walking, running, and jumping motion control technology that enables its humanoid robot "Qrio" to smoothly combine conventional walking movement with new running and jumping motions.
VMIC's CompactPCI SBC packs Intel's latest Pentium M micro Product News 12/24/2003 Post a comment GE Fanuc Automation Americas, also known to board users as VMIC, previews a new hot-swappable single-slot CompactPCI board that features Intel's latest Pentium M processor technology. The new board's processor clocks at up to 1.6-GHz, yet performs many applications comparable to a 2.4-GHz Pentium---but it dissipates half the power. Although only a preliminary datasheet is available, eeProductCenter Senior Tech Editor Alex Mendelsohn enumerates some if its salient features.
What are the engineering and design challenges in creating successful IoT devices? These devices are usually small, resource-constrained electronics designed to sense, collect, send, and/or interpret data. Some of the devices need to be smart enough to act upon data in real time, 24/7. Are the design challenges the same as with embedded systems, but with a little developer- and IT-skills added in? What do engineers need to know? Rick Merritt talks with two experts about the tools and best options for designing IoT devices in 2016. Specifically the guests will discuss sensors, security, and lessons from IoT deployments.