Breaking News
Content tagged with RF/Microwave
posted in May 2007
Tutorial on 802.11n PHY layer : Part 3
Design How-To  
5/29/2007   1 comment
Part 3: The structures of a MIMO-OFDM transmitter and receiver are analyzed and a data rate table is constructed.
Tutorial: Polar modulation and its variants
Design How-To  
5/24/2007   Post a comment
The announcement this week by Sequoia Communications of a single-chip HEDGE transceiver based on polar modulation calls out for an explanation of what polar modulation is all about and how it varies. Find out more in this special feature compilation.
Tutorial on 802.11n PHY layer: Part 2
Design How-To  
5/21/2007   Post a comment
With 802.11n, wireless achieved data rates equal to wireline. This article discusses the major aspects of the 802.11n PHY layer.
RF Fundamentals: What actually creates the 90 degree coupler phase shift? Part 3
Design How-To  
5/11/2007   Post a comment
M/A COM's Ray Kaarsberg takes the time to provide in depth details of how couplers work in this three-part technical piece. Part 3 covers the derivation of parameters, including S parameters, and conclusions derived from this analysis.
RF Fundamentals: What actually creates the 90 degree coupler phase shift? Part 2
Design How-To  
5/10/2007   2 comments
M/A COM's Ray Kaarsberg takes the time to provide in depth details of how couplers work in this three-part technical piece. Part 2 covers coupling factor, signal propagation delay, maximum coupling, and vector analysis.
RF Fundamentals: What actually creates the 90 degree coupler phase shift? Part 1
Design How-To  
5/9/2007   Post a comment
M/A COM's Ray Kaarsberg takes the time to provide in depth details of how couplers work in this three-part technical piece. Part 1 covers transmission line theory.
High precision op-amps target auto, industrial apps
Product News  
5/2/2007   Post a comment
STMicroelectronics has introduced a high-precision op-amp dubbed the TS507 that features an ultra-low input offset voltage guaranteed over a wide common-mode voltage range, making it suitable for automotive and industrial applications.


Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Radio
LATEST ARCHIVED BROADCAST

What are the engineering and design challenges in creating successful IoT devices? These devices are usually small, resource-constrained electronics designed to sense, collect, send, and/or interpret data. Some of the devices need to be smart enough to act upon data in real time, 24/7. Specifically the guests will discuss sensors, security, and lessons from IoT deployments.

Brought to you by:

Like Us on Facebook
Special Video Section
Once the base layer of a design has been taped out, making ...
In this short video we show an LED light demo to ...
The LTC2380-24 is a versatile 24-bit SAR ADC that combines ...
In this short video we show an LED light demo to ...
02:46
Wireless Power enables applications where it is difficult ...
07:41
LEDs are being used in current luxury model automotive ...
With design sizes expected to increase by 5X through 2020, ...
01:48
Linear Technology’s LT8330 and LT8331, two Low Quiescent ...
The quality and reliability of Mill-Max's two-piece ...
LED lighting is an important feature in today’s and future ...
05:27
The LT8602 has two high voltage buck regulators with an ...
05:18
Silego Technology’s highly versatile Mixed-signal GreenPAK ...
The quality and reliability of Mill-Max's two-piece ...
01:34
Why the multicopter? It has every thing in it. 58 of ...
Security is important in all parts of the IoT chain, ...
Infineon explains their philosophy and why the multicopter ...
The LTC4282 Hot SwapTM controller allows a board to be ...
This video highlights the Zynq® UltraScale+™ MPSoC, and sho...
Homeowners may soon be able to store the energy generated ...
The LTC®6363 is a low power, low noise, fully differential ...