Embedded Systems Conference
Breaking News
Content tagged with Sensors/Transducers
posted in August 2010
<<   <   Page 3 / 3
Reality check needed: New technology doubles solar conversion efficiency
SmartEnergy Designline Blog  
8/9/2010   18 comments
Researchers at Stanford have developed a cesium-coated gallium nitride PETE device that converts both light and heat into electrical energy, potentially doubling the efficiency of solar panels.
Position sensing in vehicles: how new magnetic encoder technology helps ensure accurate, fault-free sensor outputs
Design How-To  
8/9/2010   2 comments
Angle and motion sensors are widely used in vehicles for applications such as pedal position-sensing, throttle control, and in transmissions and steering wheels. It hardly needs stating that, particularly in steering systems and the throttle, reliable operation is absolutely essential to the safety of the driver, passengers, other road users and pedestrians. Automotive sensors, then, must be extremely robust, and perform reliably for the whole life of the vehicle.
Book explores the increasingly vital world of small antenna theory, design
Blog  
8/9/2010   5 comments
As products get smaller, the antenna is an integral part and challenge of the design and product
Power Tips #5: Buck-boost design uses a buck controller
Power Tips  
8/4/2010   Post a comment
A negative output voltage buck-boost, sometimes called a negative flyback, operating at 50% duty-cycle provides an output voltage equal to the input voltage, only opposite in polarity.
Power Tip 26: Current distribution in high-frequency conductors
Design How-To  
8/4/2010   15 comments
Understand how the skin effect can apply to wires, such as used in switching-converter windings
ASIC performs ambient noise cancellation during a voice call or music playback.
Product News  
8/4/2010   3 comments
Wolfson’s latest stereo headphone driver employs its proprietary digital ambient noise cancellation technology, enabling electronics manufacturers to provide consumers with cost-effective, mass market, noise canceling headphones and headsets.
<<   <   Page 3 / 3


Radio
LATEST ARCHIVED BROADCAST
As data rates begin to move beyond 25 Gbps channels, new problems arise. Getting to 50 Gbps channels might not be possible with the traditional NRZ (2-level) signaling. PAM4 lets data rates double with only a small increase in channel bandwidth by sending two bits per symbol. But, it brings new measurement and analysis problems. Signal integrity sage Ransom Stephens will explain how PAM4 differs from NRZ and what to expect in design, measurement, and signal analysis.

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Like Us on Facebook
Special Video Section
The LTC®6363 is a low power, low noise, fully differential ...
Vincent Ching, applications engineer at Avago Technologies, ...
The LT®6375 is a unity-gain difference amplifier which ...
The LTC®4015 is a complete synchronous buck controller/ ...
10:35
The LTC®2983 measures a wide variety of temperature sensors ...
The LTC®3886 is a dual PolyPhase DC/DC synchronous ...
The LTC®2348-18 is an 18-bit, low noise 8-channel ...
The LT®3042 is a high performance low dropout linear ...
Chwan-Jye Foo (C.J Foo), product marketing manager for ...
The LT®3752/LT3752-1 are current mode PWM controllers ...
LED lighting is an important feature in today’s and future ...
Active balancing of series connected battery stacks exists ...
After a four-year absence, Infineon returns to Mobile World ...
A laptop’s 65-watt adapter can be made 6 times smaller and ...
An industry network should have device and data security at ...
The LTC2975 is a four-channel PMBus Power System Manager ...
In this video, a new high speed CMOS output comparator ...
The LT8640 is a 42V, 5A synchronous step-down regulator ...
The LTC2000 high-speed DAC has low noise and excellent ...
How do you protect the load and ensure output continues to ...