Breaking News
RF & Microwave Designline Blog

RFID hits me in wallet, literally

NO RATINGS
View Comments: Threaded | Newest First | Oldest First
Dick James
User Rank
Manager
re: RFID hits me in wallet, literally
Dick James   8/12/2009 3:29:43 PM
NO RATINGS
Try DIFRwear.. http://www.semiaccurate.com/2009/08/01/block-rfid-readers-your-wallet/

Televi
User Rank
Rookie
re: RFID hits me in wallet, literally
Televi   8/12/2009 4:22:08 PM
NO RATINGS
RFID is more a resonant tank circuit than just an antenna. Hence it is the matching circuit that is more important. Two suggestions 1 Mechanically break the circuit by punching a hole or taking a blade and cut the transmission line. Credit card is still valid. 2. The other way is putting near a heater. This will make the passive components (inductors or capacitors to unsolder) and then remove those components. Or if you are expert in soldering, you can slowly unsolder the capacitors and even carefully remove the antenna.

Mag Guy
User Rank
Rookie
re: RFID hits me in wallet, literally
Mag Guy   8/12/2009 4:30:42 PM
NO RATINGS
My bank has yet to issue RFID credit cards to me so I have not seen one. My caution would be to be sure that the old magnetic "swipe stripe" is available or the card will be pretty useless except for 'net transactions. Not many business have the old card imprint machines anymore!

L_P
User Rank
Rookie
re: RFID hits me in wallet, literally
L_P   8/12/2009 6:08:17 PM
NO RATINGS
The silvery Metallized ESD shielding bags will work. Note: pink anti-static bags are non-conductive, and will NOT work.

Howard1234
User Rank
Rookie
re: RFID hits me in wallet, literally
Howard1234   8/12/2009 6:45:40 PM
NO RATINGS
Let me get this straight. You prefer a mag stripe that can be copied by anyone with a mag stripe reader against a device using advanced cryptography. There have been massive amounts of fraud here due to thieves connecting their mag stripe readers to bank machines and similar places. They have already figured out how to get your mag stripe information. Realistically you can't protect your mag stripe data unless you can identify every make and model of reader and where they are legitimately used. Also clearly you haven't bought gas outside in a Canadian winter. If you insist on shielding there are shielding sleeves made for passports with RFID in the passports. I'd get one of these and cut it down to size. At least that way you could actually use the card. I suspect without the RFID your card will declined as likely fraudulent.

agibson0307
User Rank
Rookie
re: RFID hits me in wallet, literally
agibson0307   8/19/2009 2:46:43 PM
NO RATINGS
Does shielding work? do your own experiment and find out. http://www.rfid-shield.com/info_doesitwork.php I have heard that the cards can be scanned more than 3 feet away. http://www.trolleyscan.com/newslett.html This link was not the one that I was looking for, but does help back up the claim of over 3 feet. Just need a briefcase, with a high powered reader, to grab all the information from passing people. Not all readers are set to low power reading at 1 to 6 inches. To disable the see through card that I have in my hand, cut the antenna that circles the out edge of the card. The antenna wires are up to a quarter of an inch from the edge.

the real biff44
User Rank
Rookie
re: RFID hits me in wallet, literally
the real biff44   8/22/2009 5:40:50 AM
NO RATINGS
If you really do not care much about your card, I'll bet 10 seconds in the microwave oven will fry any rfid chip inside. Not sure if the magnetic strip will still have your code on it though. maybe put the card partway submerged in water so the magnetic strip does not heat up, but the upper part is exposed to allow bigtime currents to flow in the RFID receiver input.

wb9ddf
User Rank
Rookie
re: RFID hits me in wallet, literally
wb9ddf   9/2/2009 2:04:21 PM
NO RATINGS
A little aluminum foil in the adjacent compartments in your billfold should shield and detune the antenna enough that it can only be read when you take it out to use it. That should take care of all but the most creative thieves.

More Blogs from RF & Microwave Designline Blog
I love Bluetooth. Little did I know, seventeen years ago when I was assigned my first project to write about the origins of Bluetooth and the viking that inspired the name that it would bring so much joy and convenience to my life
The main point of this blog is to point out that there is a major shift in LDMOS technology for cellular applications and the device operating voltage is changing from the current 28V range up into the 48V region.
Last week, JEDEC announced a new standard for wide I/O mobile DRAM: JESD229 Wide I/O Single Data Rate (SDR).
According to the opinion-site SodaHead.com, the iPhone 4S is the best new gadget of 2011.
I just heard from Mobile Future about a video they made summarizing the 2011 top statistics in mobile
Top Comments of the Week
August Cartoon Caption Winner!
August Cartoon Caption Winner!
"All the King's horses and all the KIng's men gave up on Humpty, so they handed the problem off to Engineering."
5 comments
Like Us on Facebook

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
EE Times on Twitter
EE Times Twitter Feed
Radio
LATEST ARCHIVED BROADCAST
David Patterson, known for his pioneering research that led to RAID, clusters and more, is part of a team at UC Berkeley that recently made its RISC-V processor architecture an open source hardware offering. We talk with Patterson and one of his colleagues behind the effort about the opportunities they see, what new kinds of designs they hope to enable and what it means for today’s commercial processor giants such as Intel, ARM and Imagination Technologies.
Flash Poll