Breaking News
Engineering Investigations

Frankenstein's Fix: What's Wrong With This Picture?

Clark Jones
11/5/2013 01:04 PM EST

 5 comments   post a comment
NO RATINGS
View Comments: Oldest First | Newest First | Threaded View
Caleb Kraft
User Rank
Blogger
simple
Caleb Kraft   11/6/2013 10:32:42 AM
NO RATINGS
what a great way to test for this. I wonder if there is a tool for pinpointing heat/cold on a board. Compressed air and a heatgun seem like such broad tools.

RichQ
User Rank
CEO
Re: simple
RichQ   11/6/2013 12:00:28 PM
NO RATINGS
I've seen canned "freeze mist" with a straw delivery attachment that allowed you to chill one component at a time, and heat guns with nozzels that produced a pencil-sized stream of hot air, so it is possible to be very selective with your heating/cooling for a short time (conduction will spread things around pretty quickly). Given the crudeness of the tools available, I am very impressed with the systematic approach and gradual narrowing of the target area. But the real key was noticing the "works for awhile" symptom and correctly inferring a thermal problem. Well done!

lakehermit
User Rank
Rookie
Heat induced solder joint cracks.
lakehermit   11/6/2013 12:57:44 PM
NO RATINGS
I started doing electronics repair work in a TV shop in the early 60's. When PC boards began to show up in consumer products the problem of cracked solder joints at the lead holes became a problem for hot or heavy components having leads that passed through the board without being bent over on the bottom. This was a particular problem for resistors over 1/2 watt and tube sockets (if you missed out on tubes in school, look for vacuum tube in Wikipedia). The problem was caused by the repeated movement or thermal expansion of the lead at the soldered hole which eventually caused a crack in the solder or the trace at the edge of the solder. The problem was a great money maker for repair guys because around 70% of TVs with a given chassis would have the same failure at the same components. The bad joint could usually be spotted just by wiggling each suspect component in a dark room while watching for small sparks where the lead was soldered to the board. Once the first new TV model's problem was located, the next ones with the same chassis were easy to find. That thermal cycling problem continued for years, although not to the same extent when manufacturers learned to bend the bottom of the leads over before soldering. Finally component heat dissipation was reduced to the point where it would not cause significant thermal expansion of the joints. When I started doing equipment design in the 70's I always specified that any heavy or high wattage component would be mounted with the leads in an open rivet which was crimped in a plated hole in the board, followed by wave soldering the rivet and lead. I never had any reliability complaints about that mounting method.  


Sheetal.Pandey
User Rank
Manager
Re: Heat induced solder joint cracks.
Sheetal.Pandey   11/6/2013 1:19:35 PM
NO RATINGS
Quite agree, many problems in the board that are in adverse environmental conditions are linked to weak solder joints. I have seen couple in my experience too.

bobdvb
User Rank
Manager
Re: simple
bobdvb   11/19/2013 3:48:29 PM
NO RATINGS
I remember another legendary TV story of someone offering to improve the alignment on an old vidicon tube camera. After many hours of adjustment he pretty much got it back to where he started. Ah, the confidence of youth.

More Blogs from Engineering Investigations
You rarely get anything extra for free. Engineers who work on vision systems know this. But sometimes other people believe that just putting a camera on it constitutes an effective inspection setup.
It's really mind-boggling to think of what my hourly rate would be if I were paid for the actual time that I spent troubleshooting a problem to get to a fix. The challenge is to avoid going down a rathole.
Often water flow is used to explain basic electronics in the form of analogies. After learning the hard way, an engineer attempts to explain basic water flow in terms of electronics.
We in the EMC/EMI world often use the saying "Don't put the well next to the outhouse" to describe large EMI sources located next to very sensitive victims.
A new conveyor wreaks havoc in a newspaper printing plant, but what's to blame?
Flash Poll
Radio
LATEST ARCHIVED BROADCAST
Join our online Radio Show on Friday 11th July starting at 2:00pm Eastern, when EETimes editor of all things fun and interesting, Max Maxfield, and embedded systems expert, Jack Ganssle, will debate as to just what is, and is not, and embedded system.
Like Us on Facebook

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
EE Times on Twitter
EE Times Twitter Feed
Top Comments of the Week