Breaking News
Engineering Investigations

Troubleshooting a Plumbing Problem the Electronics Way

NO RATINGS
View Comments: Oldest First | Newest First | Threaded View
Page 1 / 4   >   >>
Michael Dunn
User Rank
Manager
Toilet
Michael Dunn   5/29/2014 1:21:24 PM
NO RATINGS
Now if I could just figure out why one (and only one) of my toilets "sucks out" after flushing until there's an air gap in the bowl...

 

Michael Dunn
User Rank
Manager
Solderless breadboard
Michael Dunn   5/29/2014 1:24:18 PM
NO RATINGS
I have no issues soldering pipe (though yeah, it's gotta be dry)! But I now use other methods whenever feasible. Compression fittings are great. And there's a newish system called Sharkbite (I think) where fittings just press on. Sweet!

 

Crusty1
User Rank
CEO
Re: Toilet
Crusty1   5/29/2014 1:36:16 PM
NO RATINGS
Your problem is there should be an air bleed, if one toilet outflow is above another. Is there a breather pipe above the sewer pipe, it helps to stop the ball of water sucking.

Michael Dunn
User Rank
Manager
Re: Toilet
Michael Dunn   5/29/2014 1:54:45 PM
NO RATINGS
I've thought it might be related to venting, but could never figure out exactly what the problem was (or as Glen might say, the equivalent circuit). There are two vents on the roof...

Can you explain exactly where the breather needs to be, and what is causing the suction?

This toilet is on the main floor – there's one above and one below, which don't have this problem. Also, nothing affects the slow, steady suckout of the afflicted bowl (takes a couple minutes). I can flush other toilets and run other water – no impact on the current sink..., uh, current bowl.

 

zeeglen
User Rank
Blogger
Re: Toilet
zeeglen   5/29/2014 7:08:22 PM
NO RATINGS
@Michael There are two vents on the roof...

Maybe there should be a third vent that never got installed.  Or maybe one is clogged by a bird nest or dead squirrel.

Still remember seeing a schematic for a (Tek?) scope that showed a little cartoon image in the margin beside a BNC connector.  The image was a wash basin on the outside of a small shack.  The draftsperson had a sense of humour, the connector was labelled "external sync".

Crusty1
User Rank
CEO
Re: Toilet
Crusty1   5/30/2014 3:08:09 AM
NO RATINGS
It's an interesting problem especially if the upstream and down stream bowls do not cause the problem bowl to suck or rise and fall.

I do not sure there is the equivalent of a syphon, in an electronic circuit? I am sure there is someone out there that can say there is.

I had this problem once on a house I refurbished, turned out that the bowl was the problem the geometry of the the P or S outflow from the bowl was that the outfall side was slightly lower than the standing water height in the bowl should be, and thus it sucked.

If you have a cheap e-bay USB waterproof camera "enderscope" you might be able to see what the inside of the pipe is like on the affected bowl and outflow.

 

David Ashton
User Rank
Blogger
Re: Toilet
David Ashton   5/30/2014 4:36:03 AM
NO RATINGS
Hi Crusty.....  "I do not sure there is the equivalent of a syphon, in an electronic circuit? I am sure there is someone out there that can say there is."

Nice challenge!!  How about a diac or a thyristor in a Capacitor-Discharge Ignirion or photoflash circuit?  The cap represents the bucket of water, which will not be drained unitl the diac reaches its breakdown voltage (ie the level of the water is high enough, like an automatic toilet flush) or the thyristor is triggered (ie the syphon is primed) ??

Crusty1
User Rank
CEO
Re: Toilet
Crusty1   5/30/2014 5:21:53 AM
NO RATINGS
Hi David: Near but not quite I think.

The syphon automatically stops when both input and output are the same level in height, if we consider an S bend syphon, so to say.

I think we have to add the electrical equavilant of barometric pressure on both sides of the syphon in our wish to show this plumbing as a circuit.

Do you think Max might take up the challange and write an electronics stater manual for plubmbers?

Did you see Jacks new FPGA board on Kickstarter, I like it a lot.

tmiller11147
User Rank
Rookie
Plumbing problem
tmiller11147   5/30/2014 2:40:05 PM
NO RATINGS
Sure hate to tell you this but that pin hole may be due to acidic water. You might get it tested to see if the pH is below 7.2 or so. The acid etches away the inside of copper pipe. If that is so, I would expect you will have more leaks in the future.

 

zeeglen
User Rank
Blogger
Syphon
zeeglen   5/30/2014 3:07:30 PM
NO RATINGS
@David or the thyristor is triggered (ie the syphon is primed) ??

Good analogy, and if you include a resistor and discharged capacitor as the thyristor load, the charged capacitor will discharge into the other capacitor. When the levels (voltage) equalizes the current will stop flowing, just like a real syphon.

Page 1 / 4   >   >>
More Blogs from Engineering Investigations
Sometimes, it's the mundane things in electrical and electronic devices that make the difference. The strain relief on an air conditioner's line cord saved the day when the unit fell out of the window.
A lack of information on a datasheet lead to system crashes from a hot-swap controller.
An analog engineer and a digital engineer join forces, use their respective skills, and pull a few bunnies out of a hat to troubleshoot a system with which they are completely unfamiliar.
You rarely get anything extra for free. Engineers who work on vision systems know this. But sometimes other people believe that just putting a camera on it constitutes an effective inspection setup.
It's really mind-boggling to think of what my hourly rate would be if I were paid for the actual time that I spent troubleshooting a problem to get to a fix. The challenge is to avoid going down a rathole.
Radio
NEXT UPCOMING BROADCAST
EE Times Senior Technical Editor Martin Rowe will interview EMC engineer Kenneth Wyatt.
Top Comments of the Week
Like Us on Facebook

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
EE Times on Twitter
EE Times Twitter Feed
Flash Poll