Over in the Dangerous Prototypes forums, Bertho Stoltiens has been sharing an interesting project that puts a blinky party on your earlobes. The Blinkring is an earring roughly 31mm in diameter with 12 LEDs spread around its face.
The concept was to use a standard Cr2032 coin cell and make a printed circuit board (PCB) that could fit around it, effectively making the PCB the battery holder. The little bit of space left over around the cell would house all the electronics necessary to run the LEDs. Stoltiens had some challenges ahead of him on this project. He would need not only a visually pleasing way of holding the battery, but also a switch that someone could manipulate easily while wearing the earrings.
The battery-holding clip was made from a paperclip. Stoltiens said in the forums that the small curves you can see on the clip supply a much-needed spring effect that allows it to sit flush on the battery after installation. On the opposite side of the PCB is the user interface switch, which is also constructed from a paperclip and has a small loop to give it some spring action. The paperclip looks surprisingly elegant in both cases. Stoltiens said on his personal blog (where you can download the schematic and firmware) that his next version will include an off-the-shelf switch; the process of shaping the switch was very labor intensive.
In addition to the physical challenges of PCB construction, he ran into issues with programming the chip. He's using a PIC12LF1552, which is not programmable by the PICKit2 programmer he was using. A workaround using the PICKit2 Device Data File Editor was necessary to move forward. On top of that, there was a physical issue. The PIC12LF1552 doesn't really have standard ISP headers for programming. Stoltiens came up with a fairly elegant solution. He added five contact points on the back of the PCB and made a custom programming dock to hold the earring when updates were needed. You'll note that the pads on the PCB are spaced at 100mil intervals, so he could use pins through verto-board as his dock.
The LEDs are arranged in six spots. Each spot has a red and a green LED. He was hoping to achieve uniform brightness through hardware, but he ultimately had to tweak the software to get the LEDs looking right. He simply has the green LEDs remain lit for roughly twice as long as the red ones during any activity.
There are several modes of activity; all can be accessed by hitting a single button. If the button is held, the unit turns off. It will wake the next time the button is pressed. Stoltiens said on his blog that the unit can run for 100-200 hours and will last for more than a year when asleep.
@Max: for that matter, I never quit wearing narrow neck ties which got some unsolicited comments saying it was too retro about 10 years ago (I hated wearing the ones as wide as my chest that is popular in the US!). And now the narrow neck ties are back and in fashion. History has a way of repeating itself in the fashion world!
I will wait for organic LED's in my shirt fabric... in the mean time take a look at the LEDs used by Death Cab for Cuties:
Disco? Wasn't that c.1980, John TraVOLTa, et al? Aren't (some of) the Bee Gee's dead? A disco full of engineers. Probably all doing the "robot". That'll bring out the women! The engrs can carefully explain their (ckt) design challenges and tradeoffs to the captivated suitors. Burn, baby, burn! And fashion? OMG. Long live our reputation.
Maybe it will be popular a hundred years from now when the components look truly retro. Otherwise, jewelry made out of electronics requires special knowledge to appreciate its inner beauty. Of course, adding a few precious stones could help.
@Caleb: I think it is difficult to do electronic jewelry in a truly fashionable way.
At the current time I totally agree -- but what of the future. I know I read too much science fiction, but do you remember the part in Asimov's Foundation Trilogy that involves some jewelry that generates a sort of glittering field around its wearer ... I bet that would go down well at a disco!
I think it is difficult to do electronic jewelry in a truly fashionable way. Aside from teh fact that many electronics designers are far from fashion designers, the concept of subtlety is often overlooked.
Sounds like the nexus between tinkering, fashion and the IoT to me!
Philips has pursued LEDs in all sorts of clothing as a fashion statement for several years. I don't think it has caught on but I wonder why not. It seems fun, especially for the tinkerer types who might prefer making this kind of jewelry to the sort that uses stones.
Yeah, I doubt he was going for groundbreaking, or even highly fashionable. I think this was more an exercise to improve his pcb making and learn new skills. The way the battery is mounted is fairly interesting and the paperclip was surely a learning experience.
David Patterson, known for his pioneering research that led to RAID, clusters and more, is part of a team at UC Berkeley that recently made its RISC-V processor architecture an open source hardware offering. We talk with Patterson and one of his colleagues behind the effort about the opportunities they see, what new kinds of designs they hope to enable and what it means for today’s commercial processor giants such as Intel, ARM and Imagination Technologies.