Breaking News
Blog

Recovering Data From a Broken SD Card Using Arduino

NO RATINGS
1 saves
View Comments: Newest First | Oldest First | Threaded View
elizabethsimon
User Rank
Author
Re: Bad Memories....
elizabethsimon   6/15/2016 1:16:48 PM
NO RATINGS
I had something similar happen with a USB memory stick but no batteries to run down in that case. It was one of many that I had laying around and when I plugged it in, my PC refuesd to recognize that there was any memory there. Refused to format. Like you, I suspect that something got corrupted. This caused me to not trust the things so much. At least when a hard disk fails, you can usually recover some or most of the data.

sumona
User Rank
Rookie
Re: Good use
sumona   6/15/2016 6:42:27 AM
NO RATINGS
True! Undoutebtly this method is great but in general people also may prefer not taking much of a risk with their data and rather go for online photo recovery software available. Stellar Phoenix, Remo recover, all are great experts in this field. 

kishanthemass@gmail.com
User Rank
Author
Re: Good use
kishanthemass@gmail.com   11/11/2014 9:33:31 AM
NO RATINGS
its so great to read these words. Can anyone tell me what should i do to get my data from a broken sd card?

i have an sd card of phone in which my memorable moments are captured and its just a little cracked now i have put that memory card in nearly 20phones but every phone is replying no memory card i just want my photos which are the most memorable and my lifes imp photos how to recover that photos can u heip me please. I have been searching everywhere where i could recover the data. I am sorry if any mistakes found actually i dont know much english. thanking u and waiting for your reply 

 

banzee
User Rank
Author
Re: Good use
banzee   5/16/2014 2:16:35 AM
NO RATINGS
I have been searching for data recovery software for a while now and still not able to find a good recovery option which can work upon my corrupted memory card.. This seems like a legit solution. Though it requires you to have technical knowledge to work upon but since the solution is permanent, you would not mind spending some time to learn how you can recover you old data back..

Kinnar
User Rank
Author
That is the advantage of multiple protocol support
Kinnar   8/21/2013 2:59:13 PM
NO RATINGS
Great use of technology and knowhow, thanks to the multiple protocol support on the SD Card. I am not sure that all the SD cards will be supporting both SDIO and SDI protocol, but yes having access to the this kind of development boards will never make you helpless.

David Ashton
User Rank
Author
Bad Memories....
David Ashton   8/21/2013 6:40:41 AM
NO RATINGS
I have an even worse problem.  I have a cheap MP3 player that languished in a box for some time.  I charged it and tried to use it, only to find that it thought it had no memory (previously 1GB, built in, not on a card). I have tried everything I can think of to remedy this -  I have disconnected and reconnected the battery, tried the formatting software on the CD that came with it...etc,    As all that happened was the battery ran down, so I assume that the memory is corrupted rather than actually faulty.  The FM radio still works!  Very frustrating, even though it's only worth a few bucks.....

Caleb Kraft
User Rank
Author
Re: Good use
Caleb Kraft   8/20/2013 4:53:31 PM
I don't know how common it would be for only one of the communication system to fail. I wouldn't count on it. Then again, it can't hurt to have this in your "toolbox"

Susan Rambo
User Rank
Author
Good use
Susan Rambo   8/20/2013 12:25:06 PM
Recovering data from a broken SD card--that alone makes me want to get an Arduino.

Most Recent Comments
michigan0
 
SteveHarris0
 
realjjj
 
SteveHarris0
 
SteveHarris0
 
VicVat
 
Les_Slater
 
SSDWEM
 
witeken
Most Recent Messages
9/25/2016
4:48:30 PM
michigan0 Sang Kim First, 28nm bulk is in volume manufacturing for several years by the major semiconductor companies but not 28nm FDSOI today yet. Why not? Simply because unlike 28nm bulk the LDD(Lightly Doped Drain) to minimize hot carrier generation can't be implemented in 28nm FDSOI. Furthermore, hot carrier reliability becomes worse with scaling, That is the major reason why 28nm FDSOI is not manufacturable today and will not be. Second, how can you suppress the leakage currents from such ultra short 7nm due to the short channel effects? How thin SOI thickness is required to prevent punch-through of un-dopped 7nm FDSOI? Possibly less than 4nm. Depositing such an ultra thin film less then 4nm filum uniformly and reliably over 12" wafers at the manufacturing line is extremely difficult or not even manufacturable. If not manufacturable, the 7nm FDSOI debate is over!Third, what happens when hot carriers are generated near the drain at normal operation of 7nm FDSOI? Electrons go to the positively biased drain with no harm but where the holes to go? The holes can't go to the substrate because of the thin BOX layer. Some holes may become trapped at the BOX layer causing Vt shift. However, the vast majority of holes drift through the the un-dopped SOI channel toward the N+Source,...

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Like Us on Facebook
EE Times on Twitter
EE Times Twitter Feed