I am Mike, Doaks friend and primary maintence guy. I was an electronic weapons tec in the Navy. I keep a 100ft and 50ft coil of 22ga speaker wire with my ohm meter. I just use a cheepo $19 meter. My speaker wire has clips so clip one end to that pesky wire, roll the wire back to where you want to test and clip its other end to my negative probe. Start testing! The Navy does not teach this in school but they teach you to think! In a crisis or emergency, when your life,especially the lives of others, you better figure it out! And dont take all damn day, thats what my instructor taught us. I set for tone and in 30y its never failed me! I took 3 100ft extension cords one time, shorted one end, tested the other and got tone down 300ft of one side and 300ft back. So I streched it out, hooked one side to what I needed to test and I found my wire. Also look across other fields, a friend of mine has a phone toner! This is for 2 wire test! Its made for phones. When you pull 200 wires from the phone room and run em all over you have to know which is which! You plug this little thing into a phone jack, the other piece is a non contact wand! It will tell you which wire out of 200 you are pluged to! Super sweet! Take a phone jack with 3in phone wire hook to male plug insert in any outlet. This is going to allow you to id every outlet, light and switch and the breaker! Power must be off! Its also best to pop the breakers off the panel! thats easier than pulling wires off the breakers! I myself never tried it but I watched him do it more than once! I think its $300.
Commonly called a Tic Tracer, Triplett makes a version Sniff-It 2. With a variable setting, it beeps and flashes a light near an energized circuit. Beeping becomes more frequent the nearer you get. Rated for 5V - 600VAC, it is a non contact device great for finding live wires behind dry wall.
I think your time domain reflectometer will bounce signals off of every wire nut connection.
I just use RF out on the spec analyser, but it's kind of big to lug around.
Years ago I remember there were hand made testers that generated swept signals around 455kHz or 10.7MHz or 45MHz. You could test all the way from the antenna through to the speaker / TV screen, (AM /FM didn't matter) They relied on leakage of the IF through the front end so you didn't need to tune the radio. (If you have a spec analyserswith a tracking generator you can make a similar test signal)
For locating the other end of a single wire , I just hook up a 20.00MHz crystal oscilator to 4.5v worth of battery and attach the crystal oscillator output to the cable. You can do all this with 3 jumper cables. Then just use a FM radio tuned to 100MHz to follow the wire. You can use any crystal oscillator that has an odd harmonic in the FM band.
If I need a TDR , I just connect a Tee to the scope input, and put the "1kHz probe comp" signal into one end of the tee through say a 100ohm resistor and connect the other end to the cable. Do a calibration check on a known piece of cable and you are away!.
The small 8-wire network cable testers usually use a CD4017 counter chip to put a + on one wire at a time and use any or all of the other wires for return...so you need at least 2 wires working. You can use the same technique and a bunch of 74HC154 dedoders to expand that to 16 x n lines. So you could build yourself a custom cable checker quite cheaply if you don't mind picking up a soldering iron.
Of course, I don't know if would be worth your while doing this - I'm not sure how many pipe-organ axe-murderers there are out there.....
@Bill the continuity threshold was about 5 ohms. Of course, your value may differ!
Our lab DMMs buzz at 33 ohms - useless! So I built a bunch of "milliohm squawkers" for our techs to use. This changes delta-R of a few milliohms into a variable pitch tone so a reverse-engineering tech can audibly distinguish correct PCB connections in spite of closed relay contacts or low resistance transformer windings. Watch for it in upcoming EDN Design Ideas.