Breaking News
View Comments: Newest First | Oldest First | Threaded View
<<   <   Page 2 / 3   >   >>
David Ashton
User Rank
Blogger
Re: stripping PCBs
David Ashton   2/17/2014 7:58:00 PM
NO RATINGS
@Paul - thanks for that, never tried that but I have a compressor so will give it a go sometime.  It's always nice to hear that I'm not the only crazy guy that does this......

It's always good to keep in with storemen, they are very useful people to know!  Sounds like you have a good source of bits.  

Paul512
User Rank
Rookie
Re: stripping PCBs
Paul512   2/17/2014 6:15:25 PM
NO RATINGS
A technique I still find useful if you have an air compressor is to blast the solder off a heated component pin or wire. I just heat the pin with a soldering iron, holding the air gun tip almost touching. When the solder melts, a quick blast from the air gun blows the solder clean off, usually including solder in the through-plated hole. The splattered solder is not a problem as it falls off the board or other components quite easily with a little prodding. This also works with bent-over leads which can be straightened for removal once the solder is gone.

I work here in Australia in a large research lab so I scrounge a lot of cast-off electronic gear. The most recent addition was a late-1980's electron beam machine used for e-beam lithography. This had a complete set of spare PCBs and power supplies that had never been removed from their boxes. The storemen now give me a call when anything electronic is being thrown out.

David Ashton
User Rank
Blogger
Re: Poor man's reflow oven
David Ashton   2/8/2014 2:15:57 AM
NO RATINGS
@BK11 - I have tried that and it does work.  However it's best with Surface Mount - you just shake the board and off they come!  With thru hole the solder resolidifies before you have all the chips off, and you have to wear thick gloves to handle the board, and you need patience - the boards take a good time to heat up.  Clever using it for reflow though - theremostat control and all......

bk11
User Rank
Manager
Poor man's reflow oven
bk11   2/7/2014 9:41:12 AM
NO RATINGS
I've read about several people that use an old toaster oven as a reflow oven for DIY SMT work.  It seems to me that it could also be used to strip SM & TH boards by heating them up just enough to melt the solder without destroying the components or burning the PCB.

David Ashton
User Rank
Blogger
Re: Stripping PCBs
David Ashton   2/6/2014 6:39:24 PM
NO RATINGS
@didymus7 - I have used a similar technique on some boards full of logic ICs.  Gets smelly though if you  leave it for long.

BTW I would not use your full email address as a name on the site - it's an invitation to spammers....

didymus7@hotmail.com
User Rank
Freelancer
Stripping PCBs
didymus7@hotmail.com   2/6/2014 5:25:47 PM
NO RATINGS
For a while, in the days when memory was DIP and expensive, I did a sideline business stripping memory chips from PCBs, cleaning and testing them, and selling them.  When I got scrap memory boards, they were multilayer with 50, 60, 100 chips on them.  Even a heat gun was too slow to remove that many.  I used a gas grill and a screwdriver.  You could easily tell when the solder was melting and just run the screwdriver down the middle of the row and you could strip a board in a matter of 5 minutes.  Of course, you'd lose a few into the grill, but it was quick labor.

David Ashton
User Rank
Blogger
Re: Me too...
David Ashton   2/6/2014 2:45:17 PM
NO RATINGS
@Hyman1 (and Zeeglen) - I did get some tube gear - there was lots of it around in the second-hand shops when I was a kid - but I think I came in just at the end of that era.  I never built any valve gear, though I did later get and refurbish a couple of GEC 912 10W amplifiers.  I sold them when I left Zimbabwe - now one of my regrets, though they weigh a ton and would cost heaps in excess baggage charges to get to Aussie!

hyman1
User Rank
Rookie
Me too...
hyman1   2/6/2014 2:35:21 PM
NO RATINGS
I started out at the age of 6 or 8 when I ruined my father's record player. Besides making me pay for the damage, he also gave me an old radio to tinker with. That's where my first parts came from - stripped not from PCBs, because the radio was too old to have any PCBs: A metal chassis, some tube sockets and other solder joints. Leads were long, so I could even cut parts out rather than solder (didn't have a soldering iron in these early days of my electronics obsession).

Later I got some electronics kits, and I also started to repair (instead of destroy) TV sets that others didn't want any more. Earned my first money reselling them after repair. And of course mostly used parts from other TV sets went into those repairs...

I had a friend whose father worked at IBM. Sometimes we got computer boards with lots of resistors and other strange parts, which we stripped.

I still have lots of parts from these days (now 30 years in the past) in my home lab. Sometimes I still use some of them, but where I work I also have access to a lab stock of new parts whenever I need some standard part I don't have. We have an official policy that taking parts for home-lab projects is OK. They book it on the education account ;-)

I think quite a number of technical careers start that way...

zeeglen
User Rank
Blogger
Re: Recycled Parts Market
zeeglen   2/6/2014 9:33:34 AM
NO RATINGS
Nice article, David.  My Dad was in the RCAF (Royal Canadian Air Force) and would bring home one-shot telemetry equipment from drone target practice.  Point-to-point wiring and miniature soldered-in vacuum tubes, got many resistors and capacitors out of these.

Ahhh, the good old days when an aspiring kid could take a junked TV set and rework the power transformer and horizontal output tube into a 50 watt ham radio transmitter...

David Ashton
User Rank
Blogger
Re: Recycled Parts Market
David Ashton   2/5/2014 8:28:40 PM
NO RATINGS
Hi Javi.  I know there are people in India who do this, I have heard of them getting very sick from the fumes generated when PCB gets hot.  There are of course companies who recover the gold and other precious metals from scrap boards, it's good business with metals prices as they are.

For myself, it just ensures I have a good stock of parts every time I want to build something, and I don't often have to buy stuff.  In Zimbabwe it was a definite advantage, but in Australia where parts are fairly cheap and there's overnight delivery, I wonder if I should keep doing it.  But if I just  want a couple of resistors and there's an $8 delivery charge, I still score!

<<   <   Page 2 / 3   >   >>
Most Recent Comments
_hm
 
Bert22306
 
Susan Rambo
 
Loser99
 
Max The Magnificent
 
Susan Rambo
 
Max The Magnificent
 
fandres17
 
BillM210
Flash Poll
Radio
LATEST ARCHIVED BROADCAST
Join our online Radio Show on Friday 11th July starting at 2:00pm Eastern, when EETimes editor of all things fun and interesting, Max Maxfield, and embedded systems expert, Jack Ganssle, will debate as to just what is, and is not, and embedded system.
Like Us on Facebook

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
EE Times on Twitter
EE Times Twitter Feed
Top Comments of the Week