Design Con 2015
Breaking News
News & Analysis

TSMC says equipment vendors late for 14-nm

9/7/2011 10:08 AM EDT
20 comments
NO RATINGS
Page 1 / 2 Next >
More Related Links
View Comments: Newest First | Oldest First | Threaded View
Page 1 / 2   >   >>
krisi
User Rank
CEO
re: TSMC says equipment vendors late for 14-nm
krisi   9/13/2011 9:10:58 PM
NO RATINGS
Exactly my thinking Pushkar, there is a big difference between technology feasability and economical volume production, a distinction that some commentators above seem to neglect...Kris

Pushkar Ranade
User Rank
Rookie
re: TSMC says equipment vendors late for 14-nm
Pushkar Ranade   9/13/2011 9:05:33 PM
NO RATINGS
TMSCís warning about cost/complexity of EUV at 14nm and delays in the 450mm transition supports a growing pool of evidence that the 28/20nm nodes will be in production much longer than historical life cycle. This suggests that device-level innovation will need to continue on the planar transistor platform into the foreseeable future. Foundries and design houses alike will seek to enhance power/performance trade-off and try to maximize product level benefit from 28nm/20nm technologies. A 14nm technology is certainly physically achievable, but its likely going to be limited by cost/economics.

rfab
User Rank
Rookie
re: TSMC says equipment vendors late for 14-nm
rfab   9/12/2011 1:55:29 AM
NO RATINGS
Atom power and design more relevant, because the X86 complicated than ARM

resistion
User Rank
CEO
re: TSMC says equipment vendors late for 14-nm
resistion   9/11/2011 2:54:22 PM
NO RATINGS
No company can go purely on its own anymore. At least lithographically, Intel's risk is reduced by memory makers esp. NAND flash like Micron and Toshiba. They validate existing lithography tools can go down to 1X nm. Logic half-pitch is actually a generation behind NAND flash. As for high-k, some may question if it really is advantageous. Qualcomm for example, skipped on high-k at 28 nm. And Atom power consumption is still considered pretty high. So if tsmc bet all on high-k like Intel, that would have been an instance where it would have been wrong. The newest development is the finfet or multigate, which Intel showed at 22 nm. But this technology was already available years ago. Intel should get credit for reducing the risk of transitions like these. But these transitions for Intel are for only one type of product, x86 microprocessors, which hardly applies to memory makers or fabless/foundries.

chipmonk0
User Rank
Manager
re: TSMC says equipment vendors late for 14-nm
chipmonk0   9/9/2011 6:52:39 PM
NO RATINGS
The message here is that TSMC does not have what it takes to go to 14 nm on its own. Its waiting for Intel to figure it all out and then once again will get the technology free via the equipment suppliers ( as happened with ALD for gate last HKMG ) - albeit 2 years later. What if Intel now decides to do a lot more of the tool development for future nodes in - house and thus crush these bottom - feeding pretenders ?

any1
User Rank
CEO
re: TSMC says equipment vendors late for 14-nm
any1   9/8/2011 8:15:31 PM
NO RATINGS
I would speculate that optical lithography with multiple patterning and all the other process tricks and advanced layout schemes could get us down to about 11 nm. If EUVL is not more capable and cost effective by then we will see the effective end of Moore's law.

any1
User Rank
CEO
re: TSMC says equipment vendors late for 14-nm
any1   9/8/2011 8:05:23 PM
NO RATINGS
I believe that we could indeed see 14 nm design node chips in 2015. I believe that Intel and others see a clear path for multiple patterning using optical lithography at 14 nm. But because this approach is so expensive chip companies are looking for cost reductions elsewhere - such as the economy of scale of switching to 450 mm wafers to help offset the increased expense of lithography. The bigger question is will those companies be able to make any money on those chips?

krisi
User Rank
CEO
re: TSMC says equipment vendors late for 14-nm
krisi   9/8/2011 6:14:57 PM
NO RATINGS
There is no way we will see 14nm chips in 2015. I am willing to make financial bets;-). Pls email kris.iniewski@gmail.com

docdivakar
User Rank
CEO
re: TSMC says equipment vendors late for 14-nm
docdivakar   9/8/2011 5:59:11 PM
NO RATINGS
OOPS, I meant 30um above, not 3um!

docdivakar
User Rank
CEO
re: TSMC says equipment vendors late for 14-nm
docdivakar   9/8/2011 5:57:11 PM
NO RATINGS
@RobDinsmore: agree with some points you make above. The industry is still struggling with handling thinned wafers (like 3um, as in what is needed for 3D chip stacking) at 300mm. Handling thin wafers at 450mm will be exponentially harder. Secondly, there aren't many companies left in the test space to provide wafer probing gear (probe cards, test interfaces, etc) so the cost of NRE will be quite high. I think 450mm for 2015 is too optimistic unless the market needs change drastically by then. Dr. MP Divakar

Page 1 / 2   >   >>
Radio
LATEST ARCHIVED BROADCAST
EE Times Senior Technical Editor Martin Rowe will interview EMC engineer Kenneth Wyatt.
Top Comments of the Week
Like Us on Facebook

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
EE Times on Twitter
EE Times Twitter Feed
Flash Poll