Design Con 2015
Breaking News
Design How-To

How to design a traditional radio

NO RATINGS
Page 1 / 2 Next >
More Related Links
View Comments: Oldest First | Newest First | Threaded View
Page 1 / 2   >   >>
sharps_eng
User Rank
Rookie
re: How to design a traditional radio
sharps_eng   9/29/2011 11:03:16 PM
NO RATINGS
My first radio cost £6 10s 6d, probably $150 in today's money. It had six transistors: RF oscillator/superhet mixer, two IF amplifiers, a diode detector followed by a phase splitter and push-pull amplifier driving the LS transformer. The one thing wrong was that it had wheel tuning so you couldn't flip between stations. My faithful Sony ICF-M750L 'wireless' has memory pushbuttons which work just fine, but it has a vicious synthesized 9Khz filter/tuner that prevents you detuning it a lttle to boost the audio HF; oh, and on FM you can't kill the stereo in weak signals areas, it just keeps on trying, with unlistenable results. Win some, lose some, eh? (No, we can't get DAB reliably here).

Silicon Radio
User Rank
Rookie
re: How to design a traditional radio
Silicon Radio   9/30/2011 4:00:18 AM
NO RATINGS
Si484x has the flexibility to adjust the stereo/mono blend criteria--the criteria can be set to mono in weak signal areas. I also understand other Silabs products like Si47xx also have this flexibility for memory push buttons application.

Jayakumar.Singaram
User Rank
Rookie
re: How to design a traditional radio
Jayakumar.Singaram   9/30/2011 6:08:45 AM
NO RATINGS
hi , in epigon ( www.epigon.in) Blackfin DSP based radio is ready for AM,FM,DAB and DRM etc. All radios in single IC and front can be different for different band. regards jk

Bert22306
User Rank
CEO
re: How to design a traditional radio
Bert22306   9/30/2011 7:24:56 AM
NO RATINGS
Interesting article. The questions I had, while reading it, are (1) how are FM radios built into cell phones different from this (aside from the display, which I consider to be a tangential device), and more importantly, (2) why haven't all radio chips these days incorporated digital IBOC/HD Radio/Ibiquity, call it what you will? Or perhaps even the Euro DAB system? I have a wonderful Sangean HD Radio AM/FM band tuner connected to my stereo. One of the very few such stereo tuners available. Why should HD Radio be such a rarity? It's great, it supports a lot of extra programming, there's no silly monthly fee involved, it could make the AM band useful again, as opposed to hopeless, and the chips are very cheap now. Every radio should incorporate one.

agk
User Rank
Rookie
re: How to design a traditional radio
agk   9/30/2011 8:47:20 AM
NO RATINGS
The IC can tune to MW/SW/FM bands with 2 to 3 volts their respective tuning coils connected.It needs a crystal and 2 capaciors connected externally. The stereo audio out put to be amplified for connecting the loud speakers. The IF selectivity shown is good. I just recall my first crystal radio receiver using one Ge OA79 diode antenna coil and variable capacitor and a wire antenna in the year 1968.

ReneCardenas
User Rank
Rookie
re: How to design a traditional radio
ReneCardenas   9/30/2011 6:08:43 PM
NO RATINGS
Good concept with the exception that AM band despite additional filtering, it is still susceptible to weather (for reach), and natural noise (lighting and other RF sources (engine sparks, electric motors, etc ). So that leaves FM as a cleaner option, if the stability can be adjusted and corrected with weather (environment temp), it is a nice low-cost solution, and beats the monthly-fee base satelite radio.

MButts
User Rank
Rookie
re: How to design a traditional radio
MButts   9/30/2011 7:11:15 PM
NO RATINGS
I've been a ham and shortwave radio listener since childhood, and recently picked up a Tecsun PL390 pocket radio, based on the Si4734 digitally-tuned counterpart to this chip. Its performance is impressive, especially for the price. In both the Si474x and Si484x devices tuning is kHz-stepped, not continuous or fine-stepped. At first I was disappointed, familiar as I am with classic continuous analog tuning in shortwave radios. Their Si57x oscillator has very fine tuning. But the PL390 has an Easy Tuning Method (ETM) which scans the entire HF spectrum, memorizing the frequencies with any signal at all. Then the tuning dial selects these frequencies only. I like it now that I'm used to it. The Si4734 is sensitive enough that ETM gets the weakest stations. It's an interesting alternative way to listen to a radio, certainly easier for the average person. If you're at all interested in these chips, you should try a Tecsun PL390.

Bert22306
User Rank
CEO
re: How to design a traditional radio
Bert22306   9/30/2011 7:59:30 PM
NO RATINGS
I've pretty much stopped using SW, ever since important broadcasters like the BBC have dropped off the air(except in transmissions to Africa), preferring to stream over the Internet instead. However, even SW could experience a decent revival, if it would start using something like DRM (digital radio mondiale) to improve its quality. DRM is already set up to operate over the SW band. HD Radio could easily be upgraded to do the same thing. You would be astonished at the audio quality difference between analog AM and HD Radio transnmitted over the AM band. Even for voice programs. Like night and day. I can no longer get interested in any radio that doesn't include digital reception. In fact, I can't figure out what's keeping analog-only radios on the market. Almost makes me think that the vendors are in bed with satellite radio providers, trying to get people hooked on yet another monthly fee, instead of introducing people to digital terrestrial radio the easy way. With the US system, which operates over the existing AM and FM bands, it's a complete no-brainer.

DrFPGA
User Rank
Blogger
re: How to design a traditional radio
DrFPGA   9/30/2011 10:18:07 PM
NO RATINGS
What I want is a simple internet radio to get streaming stations. Anyone have a simple design?

Bert22306
User Rank
CEO
re: How to design a traditional radio
Bert22306   9/30/2011 10:40:37 PM
NO RATINGS
My "simple design" for an Internet radio was to dedicate a PC to my audio/TV system. I got a slim design, designed to be mounted vertically or horizontally, and it looks just like any other stereo system component when mounted horizontally. Its monitor is the HDTV set (which has an RGB input, as well as HDMI, and I use RGB). PC audio, via mini-phone plug, goes to the stereo preamp, amp, speakers. Keyboard and mouse are wireless. Broadband Internet connection is 802.11n (wireless). There you go. You can listen to any streaming radio or watch any streaming TV, sound is great, image is great, and you have complete flexibility. Once you've set up your favorites, with the wireless keyboard, all the radio or TV "tuning" can be done with the mouse only. No more difficult than using a typical TV remote. Drag it on the couch next to you. Piece of cake.

Page 1 / 2   >   >>
Flash Poll
Like Us on Facebook

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
EE Times on Twitter
EE Times Twitter Feed
Top Comments of the Week