Breaking News
Design How-To

Boosting long-haul microwave capacity with 1024 QAM

NO RATINGS
Page 1 / 2 Next >
More Related Links
View Comments: Threaded | Newest First | Oldest First
JanineLove
User Rank
Blogger
re: Boosting long-haul microwave capacity with 1024 QAM
JanineLove   3/27/2012 1:46:39 PM
NO RATINGS
This struck me as a great intro to long haul microwave. It might be a great piece to share with the non-techies in your life to help explain what we do!

chanj0
User Rank
Manager
re: Boosting long-haul microwave capacity with 1024 QAM
chanj0   3/27/2012 9:22:25 PM
NO RATINGS
Excellent introductory article. The article mentioned about transmission distance. I am quite interested in knowing the theoretical maximum transmitted distance vs the modulation scheme.

old account Frank Eory
User Rank
Rookie
re: Boosting long-haul microwave capacity with 1024 QAM
old account Frank Eory   3/27/2012 10:45:56 PM
NO RATINGS
It would be interesting to know how often the system can actually operate in 1024 QAM mode in the real world. In a pure AWGN channel, 1024 QAM requires "only" four times as much power as 256 QAM at the same BER, but the situation quickly gets much worse in the presence of interference. The 25% capacity gain over 256 QAM is probably well worth the higher electric bill, but what is the effective capacity gain on a typical long-haul system? Can an operator expect to operate in 1024 QAM mode 25% of the time, 75% of the time, or what?

Eirik
User Rank
Rookie
re: Boosting long-haul microwave capacity with 1024 QAM
Eirik   3/28/2012 1:35:20 PM
NO RATINGS
I guess it's important to understand that we are talking about carrier grade long haul (transport) links here. These links are dimensioned/engineered for very high availability, typically in the range of 99.995 or 99.999 % availability. This means less than half hour of outage per year! In order to achieve these figures the links have ample fading margin; typically in the range of 30 to 40 dB. Increasing modulation to 1024QAM reduces fading margin with 6dB compared to 256QAM. The effect on availability is just a factor of about 2 (doubling the outage), considering flat fading and interference free conditions. It has very limited effect on distance, as these links are not operating at the maximum possible distance anyway (due to needed fading margin). Interference can be an issue, again the sensitivity is increased by 6dB, so it needs to be factored into the availability calculations. Higher lever modulation does not change power consumption or other factors. So bottom line; as it uses adaptive modulation it offers 25% more capacity for 99.99% of the time. For the 0.01% of the time the links will scale down to lower modulation. We are running a trial link over a 65 km path in Western Norway, using the 6.7 GHz frequency band. This has been running so far for about 2 months without even once changing to lower modulation. I hope this has helped clarify the technology.

Traces
User Rank
Rookie
re: Boosting long-haul microwave capacity with 1024 QAM
Traces   3/28/2012 10:10:53 AM
NO RATINGS
Well, for sure, you can only run 1024 QAM on "bluebird days," but that's the point of adaptive modulation. Although having this sort capability that can only be used under the right conditions would seem like a huge waste in the consumer electronics space, infrastructure is a completely different space.

inductioner
User Rank
Rookie
re: Boosting long-haul microwave capacity with 1024 QAM
inductioner   3/28/2012 11:46:51 AM
NO RATINGS
It seems to me a waste of hardware upgrade. Performance requirements such as SNR for 1024-QAM is so high that it will appear to be defensless against channel fading, not to mention interferers. With adaptive modulation, it turns out to be running as 256-QAM at best as before. But it can be a good fit to wired channels such as cable, etc.

Eirik
User Rank
Rookie
re: Boosting long-haul microwave capacity with 1024 QAM
Eirik   3/28/2012 1:45:04 PM
NO RATINGS
See comment above. This is real and in live operation. I agree that SNR requirements are more stringent but in real figures it changes SNR requirements from about 24 to 30 dB, a 6 dB difference.

jlgarry
User Rank
Rookie
re: Boosting long-haul microwave capacity with 1024 QAM
jlgarry   3/28/2012 1:32:12 PM
NO RATINGS
As a page for engineers, an analysis of the SNR requirements would have been a helpful, yet easy, edition to make this article much more thorough.

markr1
User Rank
Rookie
re: Boosting long-haul microwave capacity with 1024 QAM
markr1   3/28/2012 4:00:04 PM
NO RATINGS
Thanks for the interesting article. I'd like to know more about the additional complexity and cost needed to increase the throughput. It seems like you will definitely need more linear components, lower phase noise and maybe more DSP. Does the extra cost scale with the extra throughput? Or does it cost more than 1.25x to get 1.25x data throughput?

sierra tango
User Rank
Rookie
re: Boosting long-haul microwave capacity with 1024 QAM
sierra tango   3/28/2012 5:59:18 PM
NO RATINGS
great intro article....

EricOleary
User Rank
Rookie
re: Boosting long-haul microwave capacity with 1024 QAM
EricOleary   3/29/2012 4:27:32 PM
NO RATINGS
1024 QAM presents a huge challenge to both tx and rx. On the ttx side, 1024 QAM has a much higher peak to average power ratio which means a big issue to the non-linear power amp. Would that be a compromise between the linearisation technique and the power backoff? On the RX side, it is susceptible to multiopath fading, which can imply a very expensive adaptive equaliser to compensate it. Given the maturity of technologies such as OFDM or SC FDE, should the system be considered with one of these advanced technologies?

Eirik
User Rank
Rookie
re: Boosting long-haul microwave capacity with 1024 QAM
Eirik   4/10/2012 8:48:25 AM
NO RATINGS
Hi, indeed 1024QAM pose huge challenges in several areas. The peak to average ratio depend strongly on how the 1024QAM constellation is implemented. In the radio described in this case the peak to average for 1024QAM is really not much different to 256QAM. It does require Tx linearization and sufficient power backoff, but compared to 256QAM it’s really not very different. Long Haul microwave radios operate typically with 28-30, 40 or 56 MHz carrier bandwidth (varying with different frequency bands). With such bandwidth, it is indeed susceptible to multipath fading. The debate of OFDM vs single carrier, is not clear cut. OFDM offers both pros and cons in this area. OFDM is potentially offering better robustness to selective (multipath) fading but requires more signal processing and secondly the OFDM signal could offer better spectrum utilisation (due to the more “square” spectrum) but spectrum masks issued by the regulatory bodies (FCC, ETSI) are optimised to single carrier modulation.

ersujan
User Rank
Rookie
re: Boosting long-haul microwave capacity with 1024 QAM
ersujan   7/13/2012 11:00:47 AM
NO RATINGS
5000iP SerHello Erik Good to hear that you have used 1024 QAM over a 65 km path in Western Norway, using the 6.7 GHz frequency band. We are also looking to deploy Higher capacity Microwave Link for long distance above 65 Km using higher order modulation like 1024 QAM. Could you please share me some technical parametrs ( like TX power, antenna type, antenna dimension, antenna gain, Channel Bandwidth, Modulation,Rx level,Rx sensitivity, Fade margin,Channels) with the link budget calculation used. Which Company Microwave radio you are using for such link. Hope you information would be very helpful to me and my companyies

van13
User Rank
Rookie
re: Boosting long-haul microwave capacity with 1024 QAM
van13   1/10/2013 6:02:10 AM
NO RATINGS
Hi Eirik, Can you share technical parameters on your trial link. We also want to try a microwave system using 1024 QAM modulation. Thanks!

Most Recent Comments
Flash Poll
Radio
LATEST ARCHIVED BROADCAST
Join our online Radio Show on Friday 11th July starting at 2:00pm Eastern, when EETimes editor of all things fun and interesting, Max Maxfield, and embedded systems expert, Jack Ganssle, will debate as to just what is, and is not, and embedded system.
Like Us on Facebook

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
EE Times on Twitter
EE Times Twitter Feed
Top Comments of the Week