Typically, a production honing process is setup to use an abrasive tool with a specific grit size and bond optimized for incoming part conditions. Tool expansion to achieve the desired results and final size is programmed based on rate of time. The tool feed system performs the same way on each cycle, starting with touch-off, sensed through spindle load or the force sensed on the tool feed system. Cycle time is always the same. However, when a batch of parts comes in with a different heat treatment, distortion or a size variation, the operator must intervene because the tool may expand too quickly for part conditions and be damaged. In the opposite case with a softer-than-normal workpiece, the tool will still expand at its programmed rate, when it might have been able to expand faster to reduce cycle time. Expansion at too slow a rate may also result in glazing of the honing stones, which won't self dress if the cutting force is too low. Typically, the operator must tweak the feedrate periodically to compensate for these variables.
New tool feed technology that servo-controls the force in the tool feed system enables the machine to sense, and compensate for, these variables. The new Controlled-Force feature, which works in concert with the machine's standard rate-feed system, functions like cruise control to maintain the optimum cutting load on the honing abrasive throughout a cycle, irrespective of the incoming part's hardness, geometry or size variation. In effect, the machine can detect what is happening in the bore when the abrasive contacts it, whereas with rate-feed alone, the machine feeds the tool per the program, not according to the real conditions the part is experiencing.
With Controlled-Force honing, the machine still uses a programmed feedrate, which is then increased or decreased to maintain a setpoint for the force load on the tool feed system. If the feed force drops off, the system increases the tool feed rate to compensate – resulting in faster cycle time, as just one example. Feed force is monitored every few milliseconds during the cycle to ensure the tool always feeds at the highest rate possible for part conditions.
In a typical scenario on a small pump bore, the tool expands rapidly at the start of the cycle until the system senses 150 N of force, and then climbs gradually to its 200 N setpoint.
Controlled-Force honing is ideal for applications using metal-bond abrasives. In extensive tests with cartridge valve cages, it reduced cycle times by 25 to 50 percent. In testing with diesel cylinder liners, it cut cycle time 50 percent.
Controlled force honing also produces more consistent surface finish results. In one application with hard steel parts, standard rate-feed honing produced Rz values of 2 to 7 µm. With Controlled-Force honing, the process consistently holds Rz between 5 to 6.5 µm.
Controlled-Force honing sometimes allows use of harder, more-durable abrasive bonds, where softer bonds may have been required in the past. As a result, the part yield for a given set abrasives increases, while the abrasive cost drops. Likewise, Controlled-Force technology eliminates glazing of the abrasive, due to too little cutting force. This ensures a steady, free-cutting, self-dressing condition for maximum metal removal in the shortest possible cycle time.
Connecting rods illustrate the advantage in honing parts with varying wall thickness. The con rod has the beam on one side – so the rod is very rigid in this thicker area – and the cap on the other side where wall thickness is considerably thinner. As a result, the bore has a tendency to distort more in the weaker area during honing. On these workpieces with irregular wall thickness, Controlled-Force ensures the system never overloads the tool and distorts the bore.
Rate-feed will still be the exclusive tool feed methodology with certain honing tools that use a full wraparound sleeve of metal-bonded diamond abrasive – rather than segments of abrasive – for full contact with the bore surface. These tools are particularly useful for bridging segmented bores, multiple lands, ports, keyways or crossholes. Controlled-rate feeding provides up to five expansion profiles that can be used during a cycle for rapid part touch, cutting, sizing, finishing and spark-out.
Controlled-Force tool feed gives users a new choice to optimize cycle time, abrasive consumption and labor utilization in a production environment where batches of incoming parts may vary slightly. It is available on new machines or as a retrofit for the SV-1000 and SV-500 Series.
David Patterson, known for his pioneering research that led to RAID, clusters and more, is part of a team at UC Berkeley that recently made its RISC-V processor architecture an open source hardware offering. We talk with Patterson and one of his colleagues behind the effort about the opportunities they see, what new kinds of designs they hope to enable and what it means for today’s commercial processor giants such as Intel, ARM and Imagination Technologies.