Breaking News
Teardown

Inside a CFL bulb – Less power, longer life

4/15/2011 07:30 PM EDT
5 comments
NO RATINGS
More Related Links
View Comments: Oldest First | Newest First | Threaded View
mac_droz
User Rank
Rookie
re: Inside a CFL bulb – Less power, longer life
mac_droz   4/19/2011 9:10:06 AM
NO RATINGS
There are 4 major things (problems) that are basic for CFLs: 1. Colour - so called light temperature should always be below 4000K (nice sunny colour for domestic use) unless you're a fan of horror movies. 2. Warm start - if you want to enjoy your energy efficient light for long make sure you buy one with this feature. They're easy to spot - the warm start ones take longer to light up (about 1 sec) and the filaments light up first. This allows the gas to be heated inside to lower the ignition voltage. Most of the CFLs on the market DO NOT have it - manufacturers are sparing 30cc PTC posistor. 3. Position - if you place your CFL upside down it will live shorter because of the temperature - hot air tends to go up and if the electronics PCB is higher then the light tube then it heats more. The last CFLs I bought have even a warning on the box. 4. All (to my knowledge) CFLs at the market now DO NOT have any power factor correction therefore they draw non-sinusoidal highly distorted current (spikes with amplitude 5 times higher then RMS value). That is normally not a problem for a domestic lighting but may be a problem in a big building (neutrals wires overheating in 3 phase system) and makes the grid a bit less effective. Fortunately power drawn by CFLs (domestic) are just a small percentage of the whole power to make it a significant problem.

legg
User Rank
Rookie
re: Inside a CFL bulb – Less power, longer life
legg   4/21/2011 1:54:45 PM
NO RATINGS
It would be interesting to know what issues this IC was intended to address, save for IC-controlled inductor saturation. Few commodity CFL incandescent lamp replacements actually use an IC, while demonstrating operation over a considerably wider operating input voltage range, without apparent resonant inductor saturation issues. Perhaps this is more of an issue at 240VAC? Does the IC allow cooler operation? Generate less noise or distortion? Avoid the use of high voltage electrolytic or low temperature film capacitors? Cost less? Use mercury-free tubes? Allow hands-free assembly? Has NXP missed the boat on this one?

oreyc
User Rank
Rookie
re: Inside a CFL bulb – Less power, longer life
oreyc   4/21/2011 4:55:37 PM
NO RATINGS
I agree with you, and preheating increases life of tube considerately but it also consumes more energy, in a CFL, a few milliwats plus the added cost...and in buildings, where common areas are lit by CFLs, the PFC becomes very important because it adds up to a lot of noise and distortion, but I haven´t seen the first CFL witha PCF controller

Etmax
User Rank
Rookie
re: Inside a CFL bulb – Less power, longer life
Etmax   5/22/2011 3:10:04 AM
NO RATINGS
I had incandescents in every room in the house with the exception of the kitchen and family room where we had conventional fluorescence. we had been in the house 8 years and changed only one incandescent globe. About 4 years ago we were given a bunch of GE CFL's to replace the standard size incandescents and have replaced 3 of them already. Given the increased price of them and the greater carbon footprint I would suggest that CFL's only make financial and environmental sense in locations where they run for hours at a time, because they certainly DO NOT last longer in terms of time since first turn on as our experiment has shown. I believe the CFL industry has pulled the wool over everyone's eyes on this one. As they say, the proof of the pudding.....

ken a
User Rank
Rookie
re: Inside a CFL bulb – Less power, longer life
ken a   7/6/2011 3:48:10 PM
NO RATINGS
The standard deviation of bulb lifetime is much wider for CFL than flourescent.

August Cartoon Caption Winner!
August Cartoon Caption Winner!
"All the King's horses and all the KIng's men gave up on Humpty, so they handed the problem off to Engineering."
5 comments
Top Comments of the Week
Like Us on Facebook

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
EE Times on Twitter
EE Times Twitter Feed
Flash Poll
Radio
LATEST ARCHIVED BROADCAST
David Patterson, known for his pioneering research that led to RAID, clusters and more, is part of a team at UC Berkeley that recently made its RISC-V processor architecture an open source hardware offering. We talk with Patterson and one of his colleagues behind the effort about the opportunities they see, what new kinds of designs they hope to enable and what it means for today’s commercial processor giants such as Intel, ARM and Imagination Technologies.