Embedded Systems Conference
Breaking News
Comments
Newest First | Oldest First | Threaded View
BDSmith
User Rank
Author
re: Stupid printer tricks
BDSmith   3/2/2012 9:52:20 PM
NO RATINGS
In the late 70s, I had a job servicing line printers for a number of clients where we installed office automation (before PCs and desktop printers). I had my clients well trained to keep their hands off equipment that was not working to allow me to repair it before things got worse. One day, I got a internal call from the accounting dept that their printer was on the blink and needed me to repair it. After a short diagnosis, I discovered that one of the control boards was malfunctioning. The printer was designed with 132 printer positions for each line and a solenoid driven hammer for each position that hit a letter on a chain as it passed in front of the paper. The solenoids drew 1.5 A for a hundred milliseconds. The driver circuits drew so much power that they had to be spaced out on to 13 different cards to be cooled properly. Well this day, after I pulled the faulty control card out, I lifted the lid of the printer and opened the printer gate to show that it was out of order. I took the control card down to the shop and spent 5 minutes soldering in a chip. As I walked back to the printer room I heard screaming and smelled smoke. One of the accountants had closed the printer gate and started to print a report! Without the control card, all the drivers started firing simultaneously and continuously. They got so hot, the cards actually burst into flames. Fortunately once I pulled the power plug, the flames died out quickly. But I had half the company parading through the accounting department for the next hour asking what the stink - literally - was. Fortunately, it was easy to blame the accountant for messing with equipment under repair. There were always war stories being told through out the company about client screw-ups so when it happened in-house, everyone could relate. But we were always short on spare driver cards after that.

seleong
User Rank
Author
re: Stupid printer tricks
seleong   2/14/2011 3:52:42 PM
NO RATINGS
As Freshmen at San Jose State University in the late 70's, we did a similar prank with our SysAdmin's DEC printer located in his locked office adjacent to the huge engineering computer lab. We fed it one linefeed every minute, starting late Friday afternoon. By Monday morning, he could not open the door to his office due to the reams of paper that had relocated themselves from the box to the floor..Kids!

Jonathan Zingman
User Rank
Author
re: Stupid printer tricks
Jonathan Zingman   2/12/2011 12:10:26 AM
NO RATINGS
In the early 70's I was a summer student at Mizzou, writing an assembler in FORTRAN. I'd submit my cards and get my line printer output later. The printer was an IBM behemoth with a housing to keep the noise down, which would open automatically when the paper ran out. I got friendly with the computer operators, who informed me that there was no way to open the printer from a program. I took that as a challenge and realized that if you could simulate a paper out situation, it would open up. A few thousand overprints of a single line, followed by a page feed was sufficient to cut the paper and open the housing. We all enjoyed it until other students caught wind of the trick and started doing it. What I didn't realize was that the ribbon also didn't advance when you did that, and that we were also more or less cutting these very expensive ribbons. We were soon encouraged to stop submitting those jobs!

Sheetal.Pandey
User Rank
Author
re: Stupid printer tricks
Sheetal.Pandey   2/10/2011 11:06:50 PM
NO RATINGS
I guess that guy would never play pranks again...

zeeglen
User Rank
Author
re: Stupid printer tricks
zeeglen   2/10/2011 5:49:10 PM
NO RATINGS
One of my co-workers described the prank they used to pull on the secretary at a previous job just after grad from high school. They would sometimes solder a small electrolytic capacitor across the AC in her IBM Selectric typewriter. Poor woman never knew when her typewriter would go BANG when she turned the power on. Apparently the cap protected the fuse by blowing open first.

David Ashton
User Rank
Author
re: Stupid printer tricks
David Ashton   2/10/2011 9:33:27 AM
NO RATINGS
Bad design though, printer not being able to cope with a paper jam....there's all sorts of ways you could detect this...carriage not returning to zero position, stepper motor current....



Radio
NEXT UPCOMING BROADCAST

As we unveil EE Times’ 2015 Silicon 60 list, journalist & Silicon 60 researcher Peter Clarke hosts a conversation on startups in the electronics industry. Panelists Dan Armbrust (investment firm Silicon Catalyst), Andrew Kau (venture capital firm Walden International), and Stan Boland (successful serial entrepreneur, former CEO of Neul, Icera) join in the live debate.
Flash Poll
Top Comments of the Week
Like Us on Facebook

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Special Video Section
The LTC®4015 is a complete synchronous buck controller/ ...
10:35
The LT®3042 is a high performance low dropout linear ...
Chwan-Jye Foo (C.J Foo), product marketing manager for ...
The LT®3752/LT3752-1 are current mode PWM controllers ...
LED lighting is an important feature in today’s and future ...
Active balancing of series connected battery stacks exists ...
After a four-year absence, Infineon returns to Mobile World ...
A laptop’s 65-watt adapter can be made 6 times smaller and ...
An industry network should have device and data security at ...
The LTC2975 is a four-channel PMBus Power System Manager ...
In this video, a new high speed CMOS output comparator ...
The LT8640 is a 42V, 5A synchronous step-down regulator ...
The LTC2000 high-speed DAC has low noise and excellent ...
How do you protect the load and ensure output continues to ...
General-purpose DACs have applications in instrumentation, ...
Linear Technology demonstrates its latest measurement ...
10:29
Demos from Maxim Integrated at Electronica 2014 show ...
Bosch CEO Stefan Finkbeiner shows off latest combo and ...
STMicroelectronics demoed this simple gesture control ...
Keysight shows you what signals lurk in real-time at 510MHz ...