Design Con 2015
Breaking News
Comments
Newest First | Oldest First | Threaded View
calvinmossey
User Rank
Rookie
soldering
calvinmossey   8/7/2014 6:44:22 AM
NO RATINGS
You could present interesting soldering tips to your colleagues so they could learn more about soldering techniques and not make the same mistake again. A lot of people use Huntron Tracker test equipment to determine the cause for the failures in boards, it`s good that you told them about it and saved them a lot of time.

Doctor Bob_#1
User Rank
Rookie
re: 'Newbie' engineer and the attack of the solder blobs
Doctor Bob_#1   7/28/2011 7:06:50 PM
NO RATINGS
I used a Huntron Tracker many years as a repair technician at John Deere but according to another reply capacitors are another part that shows up faulty with the proper test equipment.

djs2571
User Rank
Rookie
re: 'Newbie' engineer and the attack of the solder blobs
djs2571   6/3/2011 8:27:55 PM
NO RATINGS
lol, I guess that would go for just about anything wouldn't it.

parity
User Rank
Rookie
re: 'Newbie' engineer and the attack of the solder blobs
parity   4/15/2011 4:27:02 AM
NO RATINGS
You are talking electronics right?

georgegrimes
User Rank
Rookie
re: 'Newbie' engineer and the attack of the solder blobs
georgegrimes   4/13/2011 6:26:07 PM
NO RATINGS
The tool is not as important and the person using it!

Rich P.
User Rank
Rookie
re: 'Newbie' engineer and the attack of the solder blobs
Rich P.   4/13/2011 4:47:31 PM
NO RATINGS
This story is a great example of the benefit of having a team with diverse backgrounds and experiences. The DMM vs. Huntron comment is a reminder that you shouldn't get stuck relying on one piece of test gear, but should understand what each tester tells you. I had a similar example from working at a contract manufacturer a few years ago. One of our customers couldn't get his techs to understand that even though their frequency counter says the oscillator is ok, a distorted waveform will kill their circuit. On the other hand, we couldn't get our techs to understand that even if an o-scope shows a pretty waveform, a counter would do a better job of telling you if you met the frequency tolerance and stability criteria.

zeeglen
User Rank
Blogger
re: 'Newbie' engineer and the attack of the solder blobs
zeeglen   4/12/2011 9:37:48 PM
NO RATINGS
Huntron Trackers can be useful. They can also be misleading. A few years ago a tech came to me for some help. The output voltage of a DC to DC converter was low, he had replaced the converter to no avail, and was stumped. His Huntron Tracker showed the same curve at the converter output for both the failed UUT and a good unit. I used a DMM to quickly determine that the converter load on the bad unit was 40 ohms compared to a few Kilohms on the good unit. A load electrolytic capacitor had gone leaky and was pulling down the voltage. The Huntron could not see any difference between the good and bad capacitors. The bad one was not open and still had it's capacitance, and was not shorted either. After that the tech believed my mantra "Never trust a Huntron". He learned how to dig deeper when the Huntron could not indicate a fault.



Flash Poll
Top Comments of the Week
Like Us on Facebook
EE Times on Twitter
EE Times Twitter Feed

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
EE Life
Frankenstein's Fix, Teardowns, Sideshows, Design Contests, Reader Content & More
Max Maxfield

Want to Present a Paper at ESC Boston 2015?
Max Maxfield
8 comments
I tell you, I need more hours in each day. If I was having any more fun, there would have to be two of me to handle it all. For example, I just heard that I'm going to be both a speaker ...

Martin Rowe

No 2014 Punkin Chunkin, What Will You Do?
Martin Rowe
Post a comment
American Thanksgiving is next week, and while some people watch (American) football all day, the real competition on TV has become Punkin Chunkin. But there will be no Punkin Chunkin on TV ...

Rich Quinnell

Making the Grade in Industrial Design
Rich Quinnell
12 comments
As every developer knows, there are the paper specifications for a product design, and then there are the real requirements. The paper specs are dry, bland, and rigidly numeric, making ...

Martin Rowe

Book Review: Controlling Radiated Emissions by Design
Martin Rowe
1 Comment
Controlling Radiated Emissions by Design, Third Edition, by Michel Mardiguian. Contributions by Donald L. Sweeney and Roger Swanberg. List price: $89.99 (e-book), $119 (hardcover).