Embedded Systems Conference
Breaking News
Comments
Newest First | Oldest First | Threaded View
adipdutt
User Rank
Author
re: Hardware mess cleaned up with software
adipdutt   5/19/2012 6:34:19 PM
NO RATINGS
Thanks for your comments and suggestions,actually it was not for defense but private industry also my company was working as a design service provider. In fact the path PWM solution went on to use when the manufacturer sourced displays from different vendors and the LED back lit current varied a lot. I agree, for a product a short time software patch may be used, but if there is really a hardware design problem, sooner it is rectified the better.

anon9303122
User Rank
Author
re: Hardware mess cleaned up with software
anon9303122   4/27/2011 2:09:44 PM
NO RATINGS
Funny thing though, sometimes in the defense industry it is cheaper to change hardware than software anytime you are working with critical systems. As it turns out the work necessary to re-certify system safety software takes a lot longer and costs a lot more money than to re-certify the hardware changes.

_hm
User Rank
Author
re: Hardware mess cleaned up with software
_hm   4/20/2011 3:26:45 AM
NO RATINGS
This may be good intermittent solution. But as kendallcp mentioned, it must not happen and it should be immediately rectified with new CCA.

kendallcp
User Rank
Author
re: Hardware mess cleaned up with software
kendallcp   4/18/2011 3:11:14 PM
NO RATINGS
We all like to get Brownie points for fixing problems like this. Ultimately, though, this is only a Band-Aid. It fixes one manifestation of shoddy layout & analog design (perhaps even provably, though probably only empirically). But what when the next batch of LDOs actually oscillate rather than just fall out of regulation? Let's not send the message that it's OK to forget about how to do good hardware design because some smart software guy can always fix it up!

cdhmanning
User Rank
Author
re: Hardware mess cleaned up with software
cdhmanning   4/18/2011 3:48:23 AM
NO RATINGS
It is always a software problem. Why? It is often easier to change software than anything else. I've fixed many electronic and even mechanical defects in software. The oddest, perhaps, was fixing a lubrication defect in software. The wrong lubricant was used to lubricate some bearings in some units. When the device got hot this caused the lube to be too thin and the mechanics would slide more freely than originally designed causing oscillation. When the lube cooled it got too thick and the operation was sluggish. Solution: replace the PID loop parameters with two sets of parameters and look at oscillation to determine which set to use.

jigish.shukla1
User Rank
Author
re: Hardware mess cleaned up with software
jigish.shukla1   4/17/2011 8:59:14 PM
NO RATINGS
Great post, very interesting work. Jigish Shukla Electronics Engineer www.knownfo.com

agk
User Rank
Author
re: Hardware mess cleaned up with software
agk   4/17/2011 2:30:28 PM
NO RATINGS
A good idea in time. Generally we just start our thinking to solve these kind of issues we get into a super solutions also we land into many more options for future product development !

Tom VanCourt
User Rank
Author
re: Hardware mess cleaned up with software
Tom VanCourt   4/15/2011 7:21:56 PM
NO RATINGS
I did the same thing on a project back in the 90's. In my case, the problem occurred during startup, turning on a daughter card with plenty of decoupling caps. Inrush to charge the caps dropped supply voltage enough to trigger the power monitor chip. That reset the system, which proceeded to turn on the daughter card, ... lather, rinse, repeat. I didn't exactly PWM, but pretty close - a slightly different kind of duty cycle modulation with the same net effect.

zeeglen
User Rank
Author
re: Hardware mess cleaned up with software
zeeglen   4/15/2011 1:14:24 AM
NO RATINGS
Nice example of how a seemingly innocuous change can suddenly turn into a butt-biting alligator snapper. Good solution with software PWM. Someone (other than management) should have received a bonus for creative thinking.

old account Frank Eory
User Rank
Author
re: Hardware mess cleaned up with software
old account Frank Eory   4/14/2011 11:27:49 PM
NO RATINGS
Nice solution. Also a good example of why managers and marketers should not assume that specs can be changed and new features added to an existing product without consequences.



Radio
LATEST ARCHIVED BROADCAST
As data rates begin to move beyond 25 Gbps channels, new problems arise. Getting to 50 Gbps channels might not be possible with the traditional NRZ (2-level) signaling. PAM4 lets data rates double with only a small increase in channel bandwidth by sending two bits per symbol. But, it brings new measurement and analysis problems. Signal integrity sage Ransom Stephens will explain how PAM4 differs from NRZ and what to expect in design, measurement, and signal analysis.

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Most Recent Comments
rick merritt
 
VicVat
 
jnissen
 
M_Alex_Nugent
 
traneus
 
David Ashton
 
perl_geek
 
Max The Magnificent
 
perl_geek
Most Recent Messages
2/9/2016
1:17:21 AM
Like Us on Facebook
Special Video Section
The LTC®6363 is a low power, low noise, fully differential ...
Vincent Ching, applications engineer at Avago Technologies, ...
The LT®6375 is a unity-gain difference amplifier which ...
The LTC®4015 is a complete synchronous buck controller/ ...
10:35
The LTC®2983 measures a wide variety of temperature sensors ...
The LTC®3886 is a dual PolyPhase DC/DC synchronous ...
The LTC®2348-18 is an 18-bit, low noise 8-channel ...
The LT®3042 is a high performance low dropout linear ...
Chwan-Jye Foo (C.J Foo), product marketing manager for ...
The LT®3752/LT3752-1 are current mode PWM controllers ...
LED lighting is an important feature in today’s and future ...
Active balancing of series connected battery stacks exists ...
After a four-year absence, Infineon returns to Mobile World ...
A laptop’s 65-watt adapter can be made 6 times smaller and ...
An industry network should have device and data security at ...
The LTC2975 is a four-channel PMBus Power System Manager ...
In this video, a new high speed CMOS output comparator ...
The LT8640 is a 42V, 5A synchronous step-down regulator ...
The LTC2000 high-speed DAC has low noise and excellent ...
How do you protect the load and ensure output continues to ...