Breaking News
Comments
Newest First | Oldest First | Threaded View
adipdutt
User Rank
Rookie
re: Hardware mess cleaned up with software
adipdutt   5/19/2012 6:34:19 PM
NO RATINGS
Thanks for your comments and suggestions,actually it was not for defense but private industry also my company was working as a design service provider. In fact the path PWM solution went on to use when the manufacturer sourced displays from different vendors and the LED back lit current varied a lot. I agree, for a product a short time software patch may be used, but if there is really a hardware design problem, sooner it is rectified the better.

anon9303122
User Rank
Freelancer
re: Hardware mess cleaned up with software
anon9303122   4/27/2011 2:09:44 PM
NO RATINGS
Funny thing though, sometimes in the defense industry it is cheaper to change hardware than software anytime you are working with critical systems. As it turns out the work necessary to re-certify system safety software takes a lot longer and costs a lot more money than to re-certify the hardware changes.

_hm
User Rank
CEO
re: Hardware mess cleaned up with software
_hm   4/20/2011 3:26:45 AM
NO RATINGS
This may be good intermittent solution. But as kendallcp mentioned, it must not happen and it should be immediately rectified with new CCA.

kendallcp
User Rank
Rookie
re: Hardware mess cleaned up with software
kendallcp   4/18/2011 3:11:14 PM
NO RATINGS
We all like to get Brownie points for fixing problems like this. Ultimately, though, this is only a Band-Aid. It fixes one manifestation of shoddy layout & analog design (perhaps even provably, though probably only empirically). But what when the next batch of LDOs actually oscillate rather than just fall out of regulation? Let's not send the message that it's OK to forget about how to do good hardware design because some smart software guy can always fix it up!

cdhmanning
User Rank
Rookie
re: Hardware mess cleaned up with software
cdhmanning   4/18/2011 3:48:23 AM
NO RATINGS
It is always a software problem. Why? It is often easier to change software than anything else. I've fixed many electronic and even mechanical defects in software. The oddest, perhaps, was fixing a lubrication defect in software. The wrong lubricant was used to lubricate some bearings in some units. When the device got hot this caused the lube to be too thin and the mechanics would slide more freely than originally designed causing oscillation. When the lube cooled it got too thick and the operation was sluggish. Solution: replace the PID loop parameters with two sets of parameters and look at oscillation to determine which set to use.

jigish.shukla1
User Rank
Rookie
re: Hardware mess cleaned up with software
jigish.shukla1   4/17/2011 8:59:14 PM
NO RATINGS
Great post, very interesting work. Jigish Shukla Electronics Engineer www.knownfo.com

agk
User Rank
Rookie
re: Hardware mess cleaned up with software
agk   4/17/2011 2:30:28 PM
NO RATINGS
A good idea in time. Generally we just start our thinking to solve these kind of issues we get into a super solutions also we land into many more options for future product development !

Tom VanCourt
User Rank
Rookie
re: Hardware mess cleaned up with software
Tom VanCourt   4/15/2011 7:21:56 PM
NO RATINGS
I did the same thing on a project back in the 90's. In my case, the problem occurred during startup, turning on a daughter card with plenty of decoupling caps. Inrush to charge the caps dropped supply voltage enough to trigger the power monitor chip. That reset the system, which proceeded to turn on the daughter card, ... lather, rinse, repeat. I didn't exactly PWM, but pretty close - a slightly different kind of duty cycle modulation with the same net effect.

zeeglen
User Rank
Blogger
re: Hardware mess cleaned up with software
zeeglen   4/15/2011 1:14:24 AM
NO RATINGS
Nice example of how a seemingly innocuous change can suddenly turn into a butt-biting alligator snapper. Good solution with software PWM. Someone (other than management) should have received a bonus for creative thinking.

old account Frank Eory
User Rank
Rookie
re: Hardware mess cleaned up with software
old account Frank Eory   4/14/2011 11:27:49 PM
NO RATINGS
Nice solution. Also a good example of why managers and marketers should not assume that specs can be changed and new features added to an existing product without consequences.



Flash Poll
Top Comments of the Week
Like Us on Facebook
EE Times on Twitter
EE Times Twitter Feed

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
EE Life
Frankenstein's Fix, Teardowns, Sideshows, Design Contests, Reader Content & More
Max Maxfield

The Best of the Best Videos on YouTube
Max Maxfield
2 comments
A couple of days ago, my chum Paul was visiting me in my office. He'd wandered over from his cubicle in the next bay to take a brief coffee break. This week, Paul had been admiring the ...

Jolt Judges and Andrew Binstock

Jolt Awards: The Best Books
Jolt Judges and Andrew Binstock
1 Comment
As we do every year, Dr. Dobb's recognizes the best books of the last 12 months via the Jolt Awards -- our cycle of product awards given out every two months in each of six categories. No ...

Engineering Investigations

Air Conditioner Falls From Window, Still Works
Engineering Investigations
2 comments
It's autumn in New England. The leaves are turning to red, orange, and gold, my roses are in their second bloom, and it's time to remove the air conditioner from the window. On September ...

David Blaza

The Other Tesla
David Blaza
5 comments
I find myself going to Kickstarter and Indiegogo on a regular basis these days because they have become real innovation marketplaces. As far as I'm concerned, this is where a lot of cool ...