Embedded Systems Conference
Breaking News
Newest First | Oldest First | Threaded View
User Rank
re: How It Was: Programming (and debugging) microprocessors
Bellhop   11/28/2011 7:44:01 PM
I too started out with the 1802. It was THE CMOS processor of the time. I hand-assembled on a legal pad and entered the data into my homemade development system rack. I had a hex keypad, hexadecimal readout (address and data), and a simple homemade debug monitor. There were some Phi-Decks laying around, so I used them to store my data. The 1802 ran the Phi-Deck too. I did a program up to 8K using this method. The Phi-Deck beat the heck out of paper tape and direct address entry with auto-increment made entering code easier. The keypad/display could also be used for data I/O during debugging and there was a single step mode and a breakpoint.

User Rank
re: How It Was: Programming (and debugging) microprocessors
Phil16v   11/22/2011 8:41:40 AM
I joined a very small company in the East Midlands (UK) in January 1979, which had no electronics department, but a requirement for some unique electronic products. They had purchased a National COPS development system, which had a hex keypad and a 7 segment display. I refused to use it, since I considered the processor inadequate for their needs, and bought a Nascom (Z80 based) kit instead. After buying the £100+ 32k dynamic RAM card kit, and the ZEAP editor assembler on ROM, I bought a Vero board, which was at at that time available with an 80 way single sided edge connector, the same as the edge connector on the RAM card and the NASCOM. I then built an 'emulator' of sorts. Address and data areas that weren't used on the main board or the RAM card were mapped out onto a 40 way ribbon cable with a 40 pin DIL plug on the end of it which was the same pinout as the Z80. A home brewed EPROM programmer was added so that I could put my developed programs into the finished hardware, and the cassette tape data storage was replaced by a 5.25" single-sided 360k floppy drive, with a ROM based disk storage system called NAS-DOS. It wasn't really a disk operating system, since it required the user to specify the area of memory to copy to or from, and the sector and track numbers to access on the disk, but it was reliable. I was so pleased with the whole system that I built another for use at home. I recall that at the time the Intel SDK with ICE was about £11k, so it was very cost effective. I still have it somewhere - reading this article has re-kindled my determination to dig it out and recommission it. I wonder if you can still buy those floppies...

David Ashton
User Rank
re: How It Was: Programming (and debugging) microprocessors
David Ashton   11/19/2011 3:18:43 AM
Wow.... I played around with an SDK-85 and also with an Osborne-1 years ago. I did some stuff on 8085s and Z80s but I remember looking at the MDS and other development stuff in my intel books (which I still have) and thinking how great it would be to have something like that. Great article, Aubrey, many thanks.

Max The Magnificent
User Rank
re: How It Was: Programming (and debugging) microprocessors
Max The Magnificent   11/18/2011 5:10:07 PM
This is fantastic Aubrey -- thank you so much for taking the time to pull this together... ...I had forgotten the process of two-pass assembly using paper tapes, but I used to do this myself... the thing is that it really isn't all that long ago that we were doing this sort of thing -- things certainly have advanced dramatically...

Top Comments of the Week
Like Us on Facebook

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
EE Life
Frankenstein's Fix, Teardowns, Sideshows, Design Contests, Reader Content & More
Max Maxfield

My Mom the Radio Star
Max Maxfield
Post a comment
I've said it before and I'll say it again -- it's a funny old world when you come to think about it. Last Friday lunchtime, for example, I received an email from Tim Levell, the editor for ...

Bernard Cole

A Book For All Reasons
Bernard Cole
1 Comment
Robert Oshana's recent book "Software Engineering for Embedded Systems (Newnes/Elsevier)," written and edited with Mark Kraeling, is a 'book for all reasons.' At almost 1,200 pages, it ...

Martin Rowe

Leonard Nimoy, We'll Miss you
Martin Rowe
Like many of you, I was saddened to hear the news of Leonard Nimoy's death. His Star Trek character Mr. Spock was an inspiration to many of us who entered technical fields.

Rich Quinnell

Making the Grade in Industrial Design
Rich Quinnell
As every developer knows, there are the paper specifications for a product design, and then there are the real requirements. The paper specs are dry, bland, and rigidly numeric, making ...

Special Video Section
After a four-year absence, Infineon returns to Mobile World ...
A laptop’s 65-watt adapter can be made 6 times smaller and ...
An industry network should have device and data security at ...
The LTC2975 is a four-channel PMBus Power System Manager ...
In this video, a new high speed CMOS output comparator ...
The LT8640 is a 42V, 5A synchronous step-down regulator ...
The LTC2000 high-speed DAC has low noise and excellent ...
How do you protect the load and ensure output continues to ...
General-purpose DACs have applications in instrumentation, ...
Linear Technology demonstrates its latest measurement ...
Demos from Maxim Integrated at Electronica 2014 show ...
Bosch CEO Stefan Finkbeiner shows off latest combo and ...
STMicroelectronics demoed this simple gesture control ...
Keysight shows you what signals lurk in real-time at 510MHz ...
TE Connectivity's clear-plastic, full-size model car shows ...
Why culture makes Linear Tech a winner.
Recently formed Architects of Modern Power consortium ...
Specially modified Corvette C7 Stingray responds to ex Indy ...
Avago’s ACPL-K30T is the first solid-state driver qualified ...
NXP launches its line of multi-gate, multifunction, ...
EE Times Senior Technical Editor Martin Rowe will interview EMC engineer Kenneth Wyatt.
Flash Poll