Design Con 2015
Breaking News
Comments
Newest First | Oldest First | Threaded View
Page 1 / 2   >   >>
GEM
User Rank
Rookie
re: A design to generate UAV electrical power in flight
GEM   7/10/2012 10:12:53 PM
NO RATINGS
jeremybirch you win the prize, this whole science experiment could have been summarized in a few paragraphs as a waste of time. I assume someone was being paid by a arm of the government to perform this demonstration, and throw away way our money. One other technical comment the aero drag caused by the heat exchanger (i.e TEG) most likely wasted significantly more energy than the TEG captured, making net energy captured negative. How about capturing the heat and use it in a closed loop vapor cycle engine (i.e. similar to air conditioner in reverse, you will get much higher efficiency than 5%)

Abrahim
User Rank
Rookie
re: A design to generate UAV electrical power in flight
Abrahim   6/28/2012 7:06:00 AM
NO RATINGS
while its possible to attain good temperature differential in such a system for a therocouple but i think that a high efficiency solar cell fitted to utilize the wing span (without destroying the aerodynamic) can be a much less cumbersome and more efficient option.

Abrahim
User Rank
Rookie
re: A design to generate UAV electrical power in flight
Abrahim   6/28/2012 7:01:47 AM
NO RATINGS
wind mill convrtr on top of a plane ! ! !

Linux28
User Rank
Rookie
re: A design to generate UAV electrical power in flight
Linux28   6/14/2012 12:10:09 PM
NO RATINGS
I've used TEGs in the past, biggest problem is reliability. They seem to have a relatively short lifetime.

Paulo540
User Rank
Rookie
re: A design to generate UAV electrical power in flight
Paulo540   6/14/2012 12:11:15 AM
NO RATINGS
I am curious what the NET power output difference is between the untouched 2-stroke motor and the one with exhaust mod... Generally, cooling off exhaust, especially of a motor with very specific exhaust parameters, will change the powerband. Speaking of motors, why no 4-stroke?

Kevin.Jackson
User Rank
Rookie
re: A design to generate UAV electrical power in flight
Kevin.Jackson   6/13/2012 8:11:42 PM
NO RATINGS
When I was nine I connected a motor's shaft to a generator and wired the generator's output to the motor. With great anticipation and excitement, I wrapped a rope around the shafts and gave it a good tug. While the shaft rotated a little longer with the wires connected than without, I clearly didn't have the perpetual motion machine I had imagined. Some years later I learned why.

Kevin.Jackson
User Rank
Rookie
re: A design to generate UAV electrical power in flight
Kevin.Jackson   6/13/2012 8:07:08 PM
NO RATINGS
I've had an interest in this approach to energy harvesting for years but Peltier devices are particularly difficult to deal with from a design standpoint (not to mention a little pricey and very inefficient). I'm happy to read of this research. I expect higher temperature devices may come out of it, which would expand the potential applications of these interesting devices.

katgod
User Rank
Rookie
re: A design to generate UAV electrical power in flight
katgod   6/13/2012 3:25:20 PM
NO RATINGS
Yes, precisely my thought also.

bharat solanki
User Rank
Rookie
re: A design to generate UAV electrical power in flight
bharat solanki   6/8/2012 2:48:35 PM
NO RATINGS
i think in car, also we lost good amount of heat energy, instead of wastage something for that also can be done...

jeremybirch
User Rank
CEO
re: A design to generate UAV electrical power in flight
jeremybirch   6/7/2012 1:51:02 PM
NO RATINGS
This system is trying to generate electricity from waste heat in the engine exhaust - not from the force of the "air" flow in the exhaust. The system was originally only 20% efficient meaning 80% was lost as heat, and some fraction of that is in the exhaust, say 30% of the overall energy. This system can capture 5% of that ie 5% of 30% which is only 1.5% of the total energy in the fuel. So at best this raises the thermal efficiency to 21.5%. As the heatsinks etc weigh quite a lot this in itself might increase the fuel consumed. I am not convinced at this level of energy extraction that it has much merit over having a generator linked to the shaft. Presumably these are TEG's are using the Peltier effect? There may be much more efficient ways to extract energy eg using Sterling engines etc

Page 1 / 2   >   >>


Top Comments of the Week
Flash Poll
Like Us on Facebook

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
EE Life
Frankenstein's Fix, Teardowns, Sideshows, Design Contests, Reader Content & More
Carlos Bueno

Adventures in Userland
Carlos Bueno
Post a comment
Editor’s Note: Excerpted from Lauren Ipsum: A Story About Computer Science and Other Improbable Things, author Carlos Bueno introduces us to Lauren and her adventures in Userland. ...

Max Maxfield

Tired Old iPad 2 vs. Shiny New iPad Air 2
Max Maxfield
9 comments
I remember when the first iPad came out deep in the mists of time we used to call 2010. Actually, that's only four years ago, but it seems like a lifetime away -- I mean; can you remember ...

Martin Rowe

Make This Engineering Museum a Reality
Martin Rowe
Post a comment
Vincent Valentine is a man on a mission. He wants to make the first house to ever have a telephone into a telephone museum. Without help, it may not happen.

Rich Quinnell

Making the Grade in Industrial Design
Rich Quinnell
16 comments
As every developer knows, there are the paper specifications for a product design, and then there are the real requirements. The paper specs are dry, bland, and rigidly numeric, making ...

Special Video Section
The LT8640 is a 42V, 5A synchronous step-down regulator ...
The LTC2000 high-speed DAC has low noise and excellent ...
How do you protect the load and ensure output continues to ...
General-purpose DACs have applications in instrumentation, ...
Linear Technology demonstrates its latest measurement ...
10:29
Demos from Maxim Integrated at Electronica 2014 show ...
Bosch CEO Stefan Finkbeiner shows off latest combo and ...
STMicroelectronics demoed this simple gesture control ...
Keysight shows you what signals lurk in real-time at 510MHz ...
TE Connectivity's clear-plastic, full-size model car shows ...
Why culture makes Linear Tech a winner.
Recently formed Architects of Modern Power consortium ...
Specially modified Corvette C7 Stingray responds to ex Indy ...
Avago’s ACPL-K30T is the first solid-state driver qualified ...
NXP launches its line of multi-gate, multifunction, ...
Doug Bailey, VP of marketing at Power Integrations, gives a ...
See how to ease software bring-up with DesignWare IP ...
DesignWare IP Prototyping Kits enable fast software ...
This video explores the LT3086, a new member of our LDO+ ...
In today’s modern electronic systems, the need for power ...