Breaking News
<<   <   Page 3 / 4   >   >>
User Rank
Author
re: Selecting a solar energy conversion method
7/9/2012 8:36:44 PM
NO RATINGS
You have stated “As the cell voltage rises, the current in the internal diode rises, leaving less of the photo current for the load”. This is not so. If you follow the panel I-V curve shown in Figure 6 when the cell voltage increases the cell current decreases. The maximum cell voltage is the open circuit voltage, Voc, where the current is zero.

User Rank
Author
re: Selecting a solar energy conversion method
7/9/2012 8:35:36 PM
NO RATINGS
The maximum power available from the panel does not change but the power that is actually extracted from the panel does change and it is a function of the load resistance RL. This maximum power point occurs when RL = Rs. The boost converter decreases the value of RL by adjusting its duty cycle. The input resistance seen by the panel is RL x (1-du)^2 where du is the duty cycle internally set by the SPV1020. The SPV1020 duty cycle is internally adjusted so that RL x (1-du)^2 equals the panel output resistance Rs.

User Rank
Author
re: Selecting a solar energy conversion method
7/9/2012 8:34:29 PM
NO RATINGS
You are correct. The intent of using the Thevenin equivalent is to show that whatever the value Rs even though non-linear, RL must match it to provide maximum power transfer.

User Rank
Author
re: Selecting a solar energy conversion method
7/9/2012 8:33:35 PM
NO RATINGS
RL will normally be much greater than Rs. Interposing the SPV1020 boost converter between the panel and RL decreases the load resistance seen by the panel. The load resistance seen by the panel Rin = RL x (1-du)^2 where du is the duty cycle internally set by SPV1020. The duty cycle is set by the SPV1020 so that RL x (1-du)^2 = Rs, the source resistance of the panel.

User Rank
Author
re: Selecting a solar energy conversion method
7/7/2012 6:29:49 PM
NO RATINGS
A very nice article with good technical details! Very much appreciated, thank you! I am wondering if this level of complexity is needed when using solar power both locally and not at normal line voltages (ie. 12V or 24V DC lighting/systems)?

User Rank
Author
re: Selecting a solar energy conversion method
7/7/2012 2:40:06 PM
NO RATINGS
I see that my understanding is slowly beginning to clear. I found the found Fig. 3.7 on pg. 24 of the following article to be helpful: https://digital.library.txstate.edu/bitstream/handle/10877/3171/fulltext.pdf I think what was bothering me was that the boost converter cannot increase the load voltage to any arbitrarily high level. It is necessarily limited by the PV maximum power curve for a given set of conditions (illumination, temp., etc.) This Fig. (3.7) seems to bear that out that.

User Rank
Author
re: Selecting a solar energy conversion method
7/6/2012 8:14:28 PM
NO RATINGS
Yes, the Thevenin model applies in figure 2, as you are looking back into the terminals of the source. What's more, if you apply a variable resistive load, you will get a linear graph of voltage vs current.

User Rank
Author
re: Selecting a solar energy conversion method
7/6/2012 7:39:23 PM
NO RATINGS
"Southern Exposure is Obvious" That is true only in the Northern Hemisphere. A better statement, might be "Equatorial Exposure is required"

User Rank
Author
re: Selecting a solar energy conversion method
7/6/2012 9:50:45 AM
NO RATINGS
Rich - as far as I am aware the panel output is surprisingly constant with time. Most panels are guaranteed more than 90% rated output after 10 years and more than 80% output after 25 years (approx 100,000 hours of daylight use). Typical results are better than that, so degradation is just a fraction of 1% per year.

User Rank
Author
re: Selecting a solar energy conversion method
7/5/2012 10:30:41 PM
NO RATINGS
Thevenin is a poor approach, a better model is a current source, with a parallel clamp diode, and better curves would include constant power profiles (V*I = constants) which makes the MPPT seeking easier to visualize.

<<   <   Page 3 / 4   >   >>

In conjunction with unveiling of EE Times’ Silicon 60 list, journalist & Silicon 60 researcher Peter Clarke hosts a conversation on startups in the electronics industry. One of Silicon Valley's great contributions to the world has been the demonstration of how the application of entrepreneurship and venture capital to electronics and semiconductor hardware can create wealth with developments in semiconductors, displays, design automation, MEMS and across the breadth of hardware developments. But in recent years concerns have been raised that traditional venture capital has turned its back on hardware-related startups in favor of software and Internet applications and services. Panelists from incubators join Peter Clarke in debate.
October 26, 1pm EDT Monday
Flash Poll

#### Datasheets.com Parts Search

##### 185 million searchable parts (please enter a part number or hit search to begin)
Special Video Section
Chwan-Jye Foo (C.J Foo), product marketing manager for ...
4:43
The LT®3752/LT3752-1 are current mode PWM controllers ...
5:11
LED lighting is an important feature in today’s and future ...
5:27
Active balancing of series connected battery stacks exists ...
9:29
After a four-year absence, Infineon returns to Mobile World ...
6:23
A laptop’s 65-watt adapter can be made 6 times smaller and ...
2:01
An industry network should have device and data security at ...
0:50
The LTC2975 is a four-channel PMBus Power System Manager ...
5:06
In this video, a new high speed CMOS output comparator ...
6:11
The LT8640 is a 42V, 5A synchronous step-down regulator ...
5:52
The LTC2000 high-speed DAC has low noise and excellent ...
5:14
How do you protect the load and ensure output continues to ...
6:54
General-purpose DACs have applications in instrumentation, ...
7:34
Linear Technology demonstrates its latest measurement ...
10:29
Demos from Maxim Integrated at Electronica 2014 show ...
4:17
Bosch CEO Stefan Finkbeiner shows off latest combo and ...
5:59
STMicroelectronics demoed this simple gesture control ...
2:15
Keysight shows you what signals lurk in real-time at 510MHz ...
4:17
TE Connectivity's clear-plastic, full-size model car shows ...
3:42
Why culture makes Linear Tech a winner.
6:08