Breaking News
Comments
Newest First | Oldest First | Threaded View
Page 1 / 2   >   >>
Kinnar
User Rank
Author
re: Using FPGAs to solve tough DSP design challenges
Kinnar   7/29/2012 6:37:20 PM
NO RATINGS
Actually what we are trying to implement using the FPGA is already there in DSP Processor, but what matters is the portability and the size reduction of the final product by implementing some functionality of DSP using FPGA, this way one will be able to reduce the use of DSP in many designs, but the real disadvantage of this method is it totally depends hardware dependent.

agk
User Rank
Author
re: Using FPGAs to solve tough DSP design challenges
agk   7/29/2012 10:56:20 AM
NO RATINGS
With FPGA's we can create massively large parallel processing so that DSP algorithms can bring useful results.

ReneCardenas
User Rank
Author
re: Using FPGAs to solve tough DSP design challenges
ReneCardenas   7/27/2012 8:29:31 PM
NO RATINGS
Thanks Nic, that is my motto, be wise enough to know that in no way we can master the universe alone, but each of us should attempt to make the universe much friendlier place to everyone. Specially new commers to engineering. There are lots of complexities and tough problems in the world, and nothing is gained by been destructive.

Alxx123
User Rank
Author
re: Using FPGAs to solve tough DSP design challenges
Alxx123   7/27/2012 4:48:55 AM
NO RATINGS
Thats all well and good but no mention or comparison on the power used in dsp vs fpga

Greg.Dee
User Rank
Author
re: Using FPGAs to solve tough DSP design challenges
Greg.Dee   7/26/2012 9:02:05 PM
NO RATINGS
no offence but "For example, a low performance DSP function that is part of a sensor or motor control system need not be implemented in a stand alone DSP device. An FPGA might be the right solution in this case." doesn't make sense to me, if it's low performance you go down the performance chain, not up it. So one would consider a general micro-controller with it's obvious advantages.

Krutsch
User Rank
Author
re: Using FPGAs to solve tough DSP design challenges
Krutsch   7/26/2012 8:05:28 PM
NO RATINGS
If only one would have to do FIR filters only…? Fact is the software stack is more complicated and it is really a pain to do it on an FPGA. For radar, some high end medical applications it might be a good choice.. For many , many applications it is a pain, try to get a solution certified for some automotive and avionics applications and you will see.

nicolas.mokhoff
User Rank
Author
re: Using FPGAs to solve tough DSP design challenges
nicolas.mokhoff   7/26/2012 3:51:59 PM
NO RATINGS
ReneCardenas: your comment on striving toward positive criticism is welcome.

ReneCardenas
User Rank
Author
re: Using FPGAs to solve tough DSP design challenges
ReneCardenas   7/26/2012 3:44:48 PM
NO RATINGS
Dr. DSP, COuldn't the same be said in the other direction?, if there are other considerations more suitable for a DSP processor then the tilt can be as well move the other direction. In my opinion, it has to be a case by case decision of the designer, given a set of resources and time constraints. Just another point of view

Medina
User Rank
Author
re: Using FPGAs to solve tough DSP design challenges
Medina   7/26/2012 3:42:56 PM
NO RATINGS
Glen, would you care to point out the anomaly in the equation? It wasn't very evident when I looked at it. Thanks

ReneCardenas
User Rank
Author
re: Using FPGAs to solve tough DSP design challenges
ReneCardenas   7/26/2012 3:32:44 PM
NO RATINGS
Glen, It is too easy to critisize and rush to jugment in haste, when it is so easy to offer the correction of such typo that appears in many publications that are transcribed by non-technical people. Simply stating the transgression in this case that the index coefficients are transposed for the constatnt term and the discrete variable term, would have accomplished more and been more informative to others that may not have see this simple transgression. Article as good merits otherwise, in my opinion.

Page 1 / 2   >   >>


Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Radio
NEXT UPCOMING BROADCAST

What are the engineering and design challenges in creating successful IoT devices? These devices are usually small, resource-constrained electronics designed to sense, collect, send, and/or interpret data. Some of the devices need to be smart enough to act upon data in real time, 24/7. Are the design challenges the same as with embedded systems, but with a little developer- and IT-skills added in? What do engineers need to know? Rick Merritt talks with two experts about the tools and best options for designing IoT devices in 2016. Specifically the guests will discuss sensors, security, and lessons from IoT deployments.
Like Us on Facebook
Special Video Section
LED lighting is an important feature in today’s and future ...
05:27
The LT8602 has two high voltage buck regulators with an ...
05:18
The quality and reliability of Mill-Max's two-piece ...
01:34
Why the multicopter? It has every thing in it. 58 of ...
Security is important in all parts of the IoT chain, ...
Infineon explains their philosophy and why the multicopter ...
The LTC4282 Hot SwapTM controller allows a board to be ...
This video highlights the Zynq® UltraScale+™ MPSoC, and sho...
Homeowners may soon be able to store the energy generated ...
The LTC®6363 is a low power, low noise, fully differential ...
See the Virtex® UltraScale+™ FPGA with 32.75G backplane ...
Vincent Ching, applications engineer at Avago Technologies, ...
The LT®6375 is a unity-gain difference amplifier which ...
The LTC®4015 is a complete synchronous buck controller/ ...
10:35
The LTC®2983 measures a wide variety of temperature sensors ...
The LTC®3886 is a dual PolyPhase DC/DC synchronous ...
The LTC®2348-18 is an 18-bit, low noise 8-channel ...
The LT®3042 is a high performance low dropout linear ...