Embedded Systems Conference
Breaking News
Comments
Newest First | Oldest First | Threaded View
Page 1 / 2   >   >>
TM123
User Rank
Author
re: Surge protection—Stop fried electronics
TM123   8/21/2012 11:59:47 PM
NO RATINGS
There is a bit more to it than just shunting off surges/spikes. The article has addressed the Ohmic requirements, but what about capacitive and inductive effects. Depending on cable lengths, there will be some considerable capacitive coupling between conductors for the duration of the surge/spike. Also multiple conductors (presumably in the same cable/conduit/duct) will suffer from inductive coupling similar to a transformer - after all we are dealing with a changing Voltage/Current waveform i.e. ac - but only for restricted cycles (hopefully only one). Some care also needs to be taken to prevent these effect through the use of shielded cables and earthed at both ends, to transform a simple shielded cable into a faraday cage in an effort to reduce these other effects. This raises a can of worms because we now have the probability of earth loops. To protect we must make some compromises. I know I would rather deal with noise reduction rather than replace everything because it has been fried!

GREATTerry
User Rank
Author
re: Surge protection—Stop fried electronics
GREATTerry   8/16/2012 3:15:55 AM
NO RATINGS
How about aiding the whole system with active clamp circuit like LTC4366? By using this kind of clamping device, the TVS can be smaller I think.

TM123
User Rank
Author
re: Surge protection—Stop fried electronics
TM123   8/15/2012 10:15:49 PM
NO RATINGS
GREAT-Terry, A Bidirectional TVS is matched to provide performance in both directions - equally. A pair of Unidirectional TVS will provide protection but will not necessarily be matched to balance the intrusion levels either side of your supply or common rails. David Ashton, fair comment on the MOV front - our particular application is inside a pressure vessel and it takes a bit over a day to pump out the gas (SF6), purge and put in walkways to access the electronics. MOVs do work but are not appropriate in our situation.

GREATTerry
User Rank
Author
re: Surge protection—Stop fried electronics
GREATTerry   8/14/2012 8:54:22 AM
NO RATINGS
Good. Is there any difference between putting 2 unidirectional TVS and a single bidirectional TVS? I usually use 2 uniderectional but frankly have no idea if a single bidirectional has poorer. Agree also to add air core inductor in series with the resistor,

David Ashton
User Rank
Author
re: Surge protection—Stop fried electronics
David Ashton   8/13/2012 12:10:19 AM
NO RATINGS
While you're fixing stuff Carolyn, on page 2 2nd para is: "6 feet of 18AWG wire has approximately .039 W resistance." W should of course be the ohms symbol - which is Capital W in Symbol Font.

David Ashton
User Rank
Author
re: Surge protection—Stop fried electronics
David Ashton   8/13/2012 12:06:58 AM
NO RATINGS
Point taken about MOVs, but they are capable of absorbing a LOT of energy, even if they fail shorted. I used to live in Zimbabwe, which has bad lightning during the summer. A company I dealt with there used big MOVs in their mains surge arrestors and they worked a treat. Better to replace a $ 35 mains surge protector than a TV/Video installation. Same company did some tests and found that a knot in the 3-core mains supply cable provided a lot of protection as well - added inductance. I used to knot all my cables after that and never had a problem with my mains inputs.

TM123
User Rank
Author
re: Surge protection—Stop fried electronics
TM123   8/12/2012 10:18:40 PM
NO RATINGS
I have found that allowing the entire voltage supply (including 0 Volts) to float enables the circuit to float around any surge/spike. In this case, there are a number of capacitors connecting various voltages, inputs and outputs to the real ground. A device I use lots of is the good old Pi Filter (or capacitor input filter) on every power supply rail, input and output, along with extra series inductors - everywhere. To date, I have protected uProcessors, and low voltage electronics (5 Volt, 12 Volt) successfully against voltage discharges around the 8 MV mark (we have electronics inside an Ion Accelerator). Warning - do not use MOVs as when they fail, they fail short which will require replacement. Use protective devices that are self recovering so the protective components do not become part of the problem.

I_B_GREEN
User Rank
Author
re: Surge protection—Stop fried electronics
I_B_GREEN   8/12/2012 9:45:57 PM
NO RATINGS
Only thing missing is an inductor in place of or in series with the resistor. Allows for much more energy withstand. fulcrums energy from (referenced in voltage)shunt protection downstream to GDT via inductor voltage rise due to di/dt. Care must be taken to not saturate core, air gap recommended.

EREBUS0
User Rank
Author
re: Surge protection—Stop fried electronics
EREBUS0   8/11/2012 8:59:41 PM
NO RATINGS
Personnally, I like my circuits fried with a touch of tobasco sauce. Seriously, you need to put protection on all of your inputs or pay the consequences. Regardless of surge or spike, over voltage destroys semiconductors in femtoseconds. Anyone remember the old UV erasable proms? I could destroy one from five feet away just from the static charge I would build up walking over the tile floor. Zaap! It's done.

TonyDave
User Rank
Author
re: Surge protection—Stop fried electronics
TonyDave   8/10/2012 8:24:29 AM
NO RATINGS
Hi, Surge? "An uninterrupted voltage increase that lasts more than a few seconds is usually called a "voltage surge" rather than a spike." Nice article about Transient protection, what about the surges. Try 150% for 1/2S (with a profile). Now thats a surge. Stokersson

Page 1 / 2   >   >>


Radio
NEXT UPCOMING BROADCAST
In conjunction with unveiling of EE Times’ Silicon 60 list, journalist & Silicon 60 researcher Peter Clarke hosts a conversation on startups in the electronics industry. One of Silicon Valley's great contributions to the world has been the demonstration of how the application of entrepreneurship and venture capital to electronics and semiconductor hardware can create wealth with developments in semiconductors, displays, design automation, MEMS and across the breadth of hardware developments. But in recent years concerns have been raised that traditional venture capital has turned its back on hardware-related startups in favor of software and Internet applications and services. Panelists from incubators join Peter Clarke in debate.
Most Recent Comments
resistion
 
resistion
 
resistion
 
R_Colin_Johnson
 
David Ashton
 
David Ashton
 
David Ashton
 
David Ashton
 
Ron Neale
Flash Poll
Top Comments of the Week
Like Us on Facebook

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Special Video Section
The LT®3042 is a high performance low dropout linear ...
Chwan-Jye Foo (C.J Foo), product marketing manager for ...
The LT®3752/LT3752-1 are current mode PWM controllers ...
LED lighting is an important feature in today’s and future ...
Active balancing of series connected battery stacks exists ...
After a four-year absence, Infineon returns to Mobile World ...
A laptop’s 65-watt adapter can be made 6 times smaller and ...
An industry network should have device and data security at ...
The LTC2975 is a four-channel PMBus Power System Manager ...
In this video, a new high speed CMOS output comparator ...
The LT8640 is a 42V, 5A synchronous step-down regulator ...
The LTC2000 high-speed DAC has low noise and excellent ...
How do you protect the load and ensure output continues to ...
General-purpose DACs have applications in instrumentation, ...
Linear Technology demonstrates its latest measurement ...
10:29
Demos from Maxim Integrated at Electronica 2014 show ...
Bosch CEO Stefan Finkbeiner shows off latest combo and ...
STMicroelectronics demoed this simple gesture control ...
Keysight shows you what signals lurk in real-time at 510MHz ...
TE Connectivity's clear-plastic, full-size model car shows ...