Embedded Systems Conference
Breaking News
Comments
Newest First | Oldest First | Threaded View
Robert.Fifield
User Rank
Author
re: Stretching the Dynamic Range of ADCs—A case study
Robert.Fifield   10/12/2012 8:25:52 AM
NO RATINGS
This technique is not suitable for applications which have signal components at very different input levels. As your mention, when one of the gain paths saturates, the signal will be sourced from a lower gain non-saturated path. It is important to note that the saturated ADC must still recover quickly when the signal is back within its range. Regards, Rob.

Robert.Fifield
User Rank
Author
re: Stretching the Dynamic Range of ADCs—A case study
Robert.Fifield   10/12/2012 8:12:31 AM
NO RATINGS
This is a general equation for the performance of an ideal ADC. It also assumes that the complete range of the ADC is exercised. Regards, Rob.

Robert.Fifield
User Rank
Author
re: Stretching the Dynamic Range of ADCs—A case study
Robert.Fifield   10/12/2012 8:05:23 AM
NO RATINGS
A feedback system is one method to help correct amplitude matching, another method is to correct using post processing in the digital domain. Regards, Rob.

Richard.Picado
User Rank
Author
re: Stretching the Dynamic Range of ADCs—A case study
Richard.Picado   10/11/2012 4:55:42 PM
NO RATINGS
I wonder how the system avoids over-drive/saturation of the mid-range and low-end ADCs when a very strong signal (within the high-end range) is present at the very input before the split, for example in a broadband multi-carrier scenario where multiple different narrowband signals may get into the system each with very different input levels. Or probably the application as discuss by Mr. Fifield is for a single wideband signal therefore saturation of the lower-end ADCs can be discarded. Anyway, very interesting setup.

fshah
User Rank
Author
re: Stretching the Dynamic Range of ADCs—A case study
fshah   10/11/2012 3:28:21 PM
NO RATINGS
More than two decades ago I got into a similar problem for current measurement in an energy meter requiring high dynamic range. I easily solved the problem by using a programmable gain amplifier using analog switches and an op-amp. It worked like a charm for such a slow speed application using a home grown double sided board. Farooq Shah

Brakeshoe
User Rank
Author
re: Stretching the Dynamic Range of ADCs—A case study
Brakeshoe   10/11/2012 12:55:08 PM
NO RATINGS
Quick question on footnote [2]: "The calculation for ENOB is: (dynamic range – 1.76)/6.02" I've never seen this equation before: Is it specific to the system, or does this apply to any number of ADC's?

agk
User Rank
Author
re: Stretching the Dynamic Range of ADCs—A case study
agk   10/11/2012 11:26:58 AM
NO RATINGS
The design and test of this stacked ADC is quite interesting. To perfect this the analog gain amplifiers need to have very good matching in phase and amplitude. Probably i feel that if there is a control with feed back between these gain stages in the stacked system the performance may be further improved.

Douglas.Butler
User Rank
Author
re: Stretching the Dynamic Range of ADCs—A case study
Douglas.Butler   10/10/2012 1:58:43 PM
NO RATINGS
A few years ago I had a problem digitizing heading rate for a robot. Then I realized I needed heading data in two distinct modes. When traveling in a straight line I needed high resolution heading rate data near zero. When the robot was turning I needed low resolution data over the full voltage range. I easily solved the problem by using two 8 bit A/D channels on the same input, one through a clamped x32 amplifier. When turning I used the non-amplified signal. When traveling straight I used the amplified signal.

Navelpluis
User Rank
Author
re: Stretching the Dynamic Range of ADCs—A case study
Navelpluis   10/10/2012 8:48:30 AM
NO RATINGS
Robert, thanks for posting this conceptual story. It really triggered my chaotic brain and I directly thought about customer applications. I simply like these kind of articles, so again, thanks.



Radio
NEXT UPCOMING BROADCAST
IoT Network Shoot Out
July 16, 1pm EDT Thursday

Replay available now: A handful of emerging network technologies are competing to be the preferred wide-area connection for the Internet of Things. All claim lower costs and power use than cellular but none have wide deployment yet. Listen in as proponents of leading contenders make their case to be the metro or national IoT network of the future. Rick Merritt, EE Times Silicon Valley Bureau Chief, moderators this discussion. Join in and ask his guests questions.

Brought to you by

Flash Poll
Top Comments of the Week
Like Us on Facebook

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Special Video Section
Chwan-Jye Foo (C.J Foo), product marketing manager for ...
The LT®3752/LT3752-1 are current mode PWM controllers ...
LED lighting is an important feature in today’s and future ...
Active balancing of series connected battery stacks exists ...
After a four-year absence, Infineon returns to Mobile World ...
A laptop’s 65-watt adapter can be made 6 times smaller and ...
An industry network should have device and data security at ...
The LTC2975 is a four-channel PMBus Power System Manager ...
In this video, a new high speed CMOS output comparator ...
The LT8640 is a 42V, 5A synchronous step-down regulator ...
The LTC2000 high-speed DAC has low noise and excellent ...
How do you protect the load and ensure output continues to ...
General-purpose DACs have applications in instrumentation, ...
Linear Technology demonstrates its latest measurement ...
10:29
Demos from Maxim Integrated at Electronica 2014 show ...
Bosch CEO Stefan Finkbeiner shows off latest combo and ...
STMicroelectronics demoed this simple gesture control ...
Keysight shows you what signals lurk in real-time at 510MHz ...
TE Connectivity's clear-plastic, full-size model car shows ...
Why culture makes Linear Tech a winner.