Breaking News
Newest First | Oldest First | Threaded View
<<   <   Page 3 / 3
User Rank
re: How NOT to make a training video
mr_bandit   1/11/2013 7:26:09 PM
I think the ESD one is deliberate. He could have re-shot the video. Does give the novice a pretty good idea of what not to do...

User Rank
re: How NOT to make a training video
mike65535   1/11/2013 1:29:38 PM
What's the NRA got to do with anything, troll?

User Rank
re: How NOT to make a training video
ost0   1/11/2013 8:02:48 AM
It surely is an electronic version of jackass. The circuit board he is "testing" is surely not a realistic test. ESD tests are done while running (the electronics that is, not the tester) and in the housing too see if the discharge current runs outside the critical components. Well, you can't really SEE that, but you can see if it fails ;)

User Rank
re: How NOT to make a training video
dgreigml1   1/11/2013 6:04:27 AM
This reminds me of a slight incident 20 years ago. Testing an Xray generator LC resonator at a customer's site (US/Frog medical company). Our Scotyland lab HV breakdown test kits all had inbuilt discharge. The frog one did not. Whilst reconnecting the M8 brass nuts with a spanner I managed to have both hands connected to each end of the resonator. ~8Joules discharge, spanner bounced off the 5m high concrete roof! RHS forefinger had marks displaying the "skin effect", a weekly experience whence probing HV prototypes - 6kV @ 100kHz (+ harmonics!) and also the HV side (upto 150kV). A rather pleasant Indian engineer that I worked beside with described such white skin patches as "The skin effect". Yup, this is most definitely a rather entertaining spoof. P.S. I have been in a neural comma, off and in, for 19 months, so the brain is now just adjusting to being sentient again. Cycling is very bad for your health!!! I was about to make an apology to the frogs, however why does LibreOffice Writer not go the full distance with readline?

User Rank
re: How NOT to make a training video
chipchap42   1/11/2013 12:44:13 AM
It's got to be a spoof - the guy couldn't have been that inept. OK, maybe he's an NRA supporter and he could be, but I don't believe the editor would have left that in a supposedly serious training video.

<<   <   Page 3 / 3 Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)

What are the engineering and design challenges in creating successful IoT devices? These devices are usually small, resource-constrained electronics designed to sense, collect, send, and/or interpret data. Some of the devices need to be smart enough to act upon data in real time, 24/7. Specifically the guests will discuss sensors, security, and lessons from IoT deployments.

Brought to you by:

Like Us on Facebook
Special Video Section
The LTC2380-24 is a versatile 24-bit SAR ADC that combines ...
In this short video we show an LED light demo to ...
Wireless Power enables applications where it is difficult ...
LEDs are being used in current luxury model automotive ...
With design sizes expected to increase by 5X through 2020, ...
Linear Technology’s LT8330 and LT8331, two Low Quiescent ...
The quality and reliability of Mill-Max's two-piece ...
LED lighting is an important feature in today’s and future ...
The LT8602 has two high voltage buck regulators with an ...
Silego Technology’s highly versatile Mixed-signal GreenPAK ...
The quality and reliability of Mill-Max's two-piece ...
Why the multicopter? It has every thing in it. 58 of ...
Security is important in all parts of the IoT chain, ...
Infineon explains their philosophy and why the multicopter ...
The LTC4282 Hot SwapTM controller allows a board to be ...
This video highlights the Zynq® UltraScale+™ MPSoC, and sho...
Homeowners may soon be able to store the energy generated ...
The LTC®6363 is a low power, low noise, fully differential ...
See the Virtex® UltraScale+™ FPGA with 32.75G backplane ...
Vincent Ching, applications engineer at Avago Technologies, ...