Breaking News
Comments
Newest First | Oldest First | Threaded View
Page 1 / 3   >   >>
Greg.Brent
User Rank
Author
re: What light through yonder window breaks?
Greg.Brent   4/8/2013 2:25:04 PM
NO RATINGS
My p&p uses polyethylene for an LED diffuser on its vision system.

Max The Magnificent
User Rank
Author
re: What light through yonder window breaks?
Max The Magnificent   2/13/2013 5:43:25 PM
NO RATINGS
You are correct -- mine each have a bunch of contacts -- some of them are "switch to make" and others are "switch to break" -- plus one of the switches works as a momentary switch if you press it down (when you release it it returns to the center position) and toggle if you switch it up. They are very, VERY tasty!

David Ashton
User Rank
Author
re: What light through yonder window breaks?
David Ashton   2/13/2013 8:52:49 AM
NO RATINGS
The nice thing about these keys was that you could get 6, 8 or even more sets of contacts on a key. The most you can easily get with today's toggle switches is 4.

E-Unit
User Rank
Author
re: What light through yonder window breaks?
E-Unit   2/13/2013 8:38:36 AM
NO RATINGS
Your switches look like "Kellog Keys", they were standard telephone switches here in the UK until the "Ericcson Keys" came along. The BBC (Our national radio) had an AEI (I think!) built control room from the early 60's which htey ripped out in the 90's. It had hundreds of these, some of which were never even used. I think they were replaced by the flimsier Ericcsons shortly after. For Lamps, you can drive bulbs or LEDs from the old ULN200* family ("ULN2003" suits TTL) which will take PWM etc. And yes, bulbs will integrate the pulses mech better than LED's, especially for migraine sufferers!

Max The Magnificent
User Rank
Author
re: What light through yonder window breaks?
Max The Magnificent   2/11/2013 11:11:03 PM
NO RATINGS
LOL

Max The Magnificent
User Rank
Author
re: What light through yonder window breaks?
Max The Magnificent   2/11/2013 11:10:13 PM
NO RATINGS
I think it's called a "Useless Machine" ... I have one sitting here on my desk

David Ashton
User Rank
Author
re: What light through yonder window breaks?
David Ashton   2/11/2013 11:05:28 PM
NO RATINGS
Lamps (because of their coiled filaments) are a bit inductive, so if you PWM them at a very high frequency you just might get strange things happening. But anything in the KHz region shouldn't worry them. They are after all usually fed with 50/60 Hz...anything above that you shouldn't get any flicker. I once used an auto bulb as an RF dummy load. At 40 MHZ it was quite good, but at 80 MHz it needed a trimmer cap across it to null out the inductance. Cheaper than buying s proper load.

ndancer01
User Rank
Author
re: What light through yonder window breaks?
ndancer01   2/11/2013 10:30:53 PM
NO RATINGS
When I was at Boeing, there was a rumor going around that there was a box for the uninitiated. It was welded metal and had one button--and a sign that said, "Do not press this button." It generally sat there for less than half an hour before somebody pressed it. Contents? A battery, a latching relay, and a klaxon. In that metal box, it was loud. I was told that more than one went into the Duwamish River (which ran close to the plant).

ndancer01
User Rank
Author
re: What light through yonder window breaks?
ndancer01   2/11/2013 10:25:08 PM
NO RATINGS
I believe it was invented by Claude Shannon

ndancer01
User Rank
Author
re: What light through yonder window breaks?
ndancer01   2/11/2013 10:23:23 PM
NO RATINGS
The ultimate machine, of course, is something about the size and shape of a cigar box with one switch on the front. When you throw the switch, there's an angry buzzing inside, and a few seconds later, this mannequin hand 'ratchets' out, and turns off the switch. Then the hand pops back inside, the lid closes, and the buzzing stops. This is the ultimate machine--almost human. The only thing it does, is turn itself off.

Page 1 / 3   >   >>


Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Radio
NEXT UPCOMING BROADCAST

What are the engineering and design challenges in creating successful IoT devices? These devices are usually small, resource-constrained electronics designed to sense, collect, send, and/or interpret data. Some of the devices need to be smart enough to act upon data in real time, 24/7. Are the design challenges the same as with embedded systems, but with a little developer- and IT-skills added in? What do engineers need to know? Rick Merritt talks with two experts about the tools and best options for designing IoT devices in 2016. Specifically the guests will discuss sensors, security, and lessons from IoT deployments.
Like Us on Facebook
Special Video Section
LED lighting is an important feature in today’s and future ...
05:27
The LT8602 has two high voltage buck regulators with an ...
05:18
Silego Technology’s highly versatile Mixed-signal GreenPAK ...
The quality and reliability of Mill-Max's two-piece ...
01:34
Why the multicopter? It has every thing in it. 58 of ...
Security is important in all parts of the IoT chain, ...
Infineon explains their philosophy and why the multicopter ...
The LTC4282 Hot SwapTM controller allows a board to be ...
This video highlights the Zynq® UltraScale+™ MPSoC, and sho...
Homeowners may soon be able to store the energy generated ...
The LTC®6363 is a low power, low noise, fully differential ...
See the Virtex® UltraScale+™ FPGA with 32.75G backplane ...
Vincent Ching, applications engineer at Avago Technologies, ...
The LT®6375 is a unity-gain difference amplifier which ...
The LTC®4015 is a complete synchronous buck controller/ ...
10:35
The LTC®2983 measures a wide variety of temperature sensors ...
The LTC®3886 is a dual PolyPhase DC/DC synchronous ...
The LTC®2348-18 is an 18-bit, low noise 8-channel ...
The LT®3042 is a high performance low dropout linear ...