Breaking News
Comments
daleste
User Rank
Author
re: Single chip wraps up display, audio, touch
daleste   2/28/2013 4:32:10 AM
NO RATINGS
This sounds like a good device for IoT applications. I still don't think a 32 bit microcontroller is the right processor for these devices.

JohnM555
User Rank
Author
re: Single chip wraps up display, audio, touch
JohnM555   2/28/2013 5:18:23 PM
NO RATINGS
There is no statement about the recommended bit architecture for the host controller.

DMcCunney
User Rank
Author
re: Single chip wraps up display, audio, touch
DMcCunney   2/28/2013 6:23:13 PM
NO RATINGS
I suspect it's host controller architecture agnostic. It's a separate component, communicated with by the host controller over a bus. As long as the host can communicate with it and use the functions it provides, you likely don't *care* about host architecture. It could be ARM, x86, MIPS or something else entirely.

DMcCunney
User Rank
Author
re: Single chip wraps up display, audio, touch
DMcCunney   2/28/2013 6:31:12 PM
NO RATINGS
"I still don't think a 32 bit microcontroller is the right processor for these devices." Why *not* use a 32 bit microcontroller? The driver is usually cost, not capability. As long as it will do the needed job, you use a 16 bit or even 8 bit controller because it's *cheaper*. What happens if that's *not* the case, and there isn't a significant cost difference in using a 32 bit core? The ARM Cortex M-0 mentioned elsewhere is arguably overkill for the stated usage, but the ARM architecture is widely deployed and well understood with an existing toolchain to support development and engineers familiar with it. What you wind up with is capability you won't use, but you don't care because you get the advantages of familiarity and lower time-to-market at a total price that's probably comparable to using a lesser controller.

old account Frank Eory
User Rank
Author
re: Single chip wraps up display, audio, touch
old account Frank Eory   2/28/2013 9:34:18 PM
NO RATINGS
Four-wire resistive touch sensing? It's been quite a few years since I've seen one of those plastic, squishy touchscreens -- at least here in the U.S.



Radio
LATEST ARCHIVED BROADCAST

What are the engineering and design challenges in creating successful IoT devices? These devices are usually small, resource-constrained electronics designed to sense, collect, send, and/or interpret data. Some of the devices need to be smart enough to act upon data in real time, 24/7. Specifically the guests will discuss sensors, security, and lessons from IoT deployments.

Brought to you by:

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Like Us on Facebook
Special Video Section
With design sizes expected to increase by 5X through 2020, ...
01:48
Linear Technology’s LT8330 and LT8331, two Low Quiescent ...
The quality and reliability of Mill-Max's two-piece ...
LED lighting is an important feature in today’s and future ...
05:27
The LT8602 has two high voltage buck regulators with an ...
05:18
Silego Technology’s highly versatile Mixed-signal GreenPAK ...
The quality and reliability of Mill-Max's two-piece ...
01:34
Why the multicopter? It has every thing in it. 58 of ...
Security is important in all parts of the IoT chain, ...
Infineon explains their philosophy and why the multicopter ...
The LTC4282 Hot SwapTM controller allows a board to be ...
This video highlights the Zynq® UltraScale+™ MPSoC, and sho...
Homeowners may soon be able to store the energy generated ...
The LTC®6363 is a low power, low noise, fully differential ...
See the Virtex® UltraScale+™ FPGA with 32.75G backplane ...
Vincent Ching, applications engineer at Avago Technologies, ...
The LT®6375 is a unity-gain difference amplifier which ...
The LTC®4015 is a complete synchronous buck controller/ ...
10:35
The LTC®2983 measures a wide variety of temperature sensors ...
The LTC®3886 is a dual PolyPhase DC/DC synchronous ...