Breaking News
Comments
Newest First | Oldest First | Threaded View
<<   <   Page 2 / 2
Peter Clarke
User Rank
Author
Re: DDC Reax?
Peter Clarke   7/24/2013 5:19:56 AM
NO RATINGS
What you seem to be suggesting is that all three forms of CMOS -- FinFET, DDC and FDSOI can co-exist aiming at different types of application and market sector.

That would of course multiply up the infrastructure costs, which would be something the fabs, EDA companies and IP licensors would probably try to resist.

Which may lead to the community at large forcing a choice between DDC and FDSOI as an alternative to FinFET. FinFET is already happening and is bound to continue.

 

IJD
User Rank
Author
Re: DDC Reax?
IJD   7/24/2013 4:47:40 AM
NO RATINGS
DDC is certainly a lot more "plain vanilla" than FinFET, and is not aimng at the same market -- FinFET is aiming at the high-performance (where high-performance can mean low-power) higher-cost high-NRE market, DDC is aiming at the lower-cost lower-NRE market.

The problem with FinFET is that the NRE (design and mask) costs are very high and the cost per gate is the same or higher than 28nm bulk, so many products will just never go to FinFET, only ones with deep pockets where absolute lowest power or highest speed is worth paying for.

In terms of minimum operating voltage which is driven by device variation, both DDC and FinFET are better than bulk because the channel doping is much lower, but there is still some doping because of leakage from the deep implant used under the DDC channel and below the fin.

FDSOI variation is lower still because the channel is undoped and so should be able to run at even lower voltage and have even lower power, certainly for devices which can use more parallelism to optimise power running at a lower clock rate.

Peter Clarke
User Rank
Author
Re: DDC Reax?
Peter Clarke   7/24/2013 2:10:13 AM
NO RATINGS
Operating the DDC technology at 0.425 volts was discussed in a paper from Fujitsu engineers at IEDM 2011. That is for an SRAM block, which is less tolerant of low voltage than logic. I think the recent benchmarking exercise was deliberately done at 0.9 and 1.2 volts (on the same 65 nm process as the earlier paper) so that comparisons could be made between conventional and DDC CMOS could be made more easily. I suspect that if the comparisons were made at 0.6 volts they would favor DDC even more markedly. What would really be interesting would be comparisons between DDC and FDSOI. Perhaps Globalfoundries and ARM could facilitate that. More likely they have already done, or are doing that work and are keeping the results to themselves for competitive advantage.

US Made
User Rank
Author
Re: DDC Reax?
US Made   7/23/2013 5:50:38 PM
NO RATINGS
Droping to 0.9 V is not so impressive, you could do much more with finfet.   Going away from plain vanila process technology is diastrous for business.   No huge value for this risk.

Tom Murphy
User Rank
Author
DDC Reax?
Tom Murphy   7/23/2013 2:00:19 PM
NO RATINGS
This seems to be based on reports from SuVolta. While the claims are interesting, I wondered: What is the reaction from others in the industry?    Is DDC broadly perceived by more impartial observers as a significant advance? 

<<   <   Page 2 / 2


Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Most Recent Comments
Like Us on Facebook
Special Video Section
5G LTE is on the way. These systems will require more ...
Protecting sensitive electronic circuitry from voltage ...
09:45
Watch as a web server authenticates or rejects a water ...
Protecting sensitive electronic circuitry from voltage ...
Watch as a web server authenticates or rejects a water ...
Protecting sensitive electronic circuitry from voltage ...
Power can be a gating factor in success or failure of ...
Get to market faster and connect your next product to the ...
00:44
See how microQSFP is setting a new standard for tomorrow’s ...
The LTC3649 step-down regulator combines key features of a ...
Once the base layer of a design has been taped out, making ...
In this short video we show an LED light demo to ...
The LTC2380-24 is a versatile 24-bit SAR ADC that combines ...
In this short video we show an LED light demo to ...
02:46
Wireless Power enables applications where it is difficult ...
07:41
LEDs are being used in current luxury model automotive ...
With design sizes expected to increase by 5X through 2020, ...
01:48
Linear Technology’s LT8330 and LT8331, two Low Quiescent ...
The quality and reliability of Mill-Max's two-piece ...