Breaking News
Comments
Newest First | Oldest First | Threaded View
Page 1 / 3   >   >>
Max The Magnificent
User Rank
Blogger
Re: soldering
Max The Magnificent   7/28/2014 10:32:59 AM
NO RATINGS
@richardid: The small company he is working for is well known for it`s quality chips and the managers try to keep this way by sending their engineers to make soldering trainings.

That's wonderful to hear that the managers make sure the employees have these skills.

richardit
User Rank
Rookie
soldering
richardit   7/23/2014 11:14:54 AM
NO RATINGS
My best friend presented to the engineers from his workplace valuable soldering tips that would allow them to create more durable electronic components. The small company he is working for is well known for it`s quality chips and the managers try to keep this way by sending their engineers to make soldering trainings.

zeeglen
User Rank
Blogger
Re: What soldering?
zeeglen   9/16/2013 10:19:04 AM
NO RATINGS
Being able to UN-solder any component without pulling pads off the board is an art in itself. I've worked at places where engineers were not allowed to solder unless they first proved their skills to the boss, and with good reason!  Will never forget the young eng who butchered about 10 prototype boards replacing "bad" DRAM controllers before finally concluding that maybe there was an error in his design.

Duane Benson
User Rank
Blogger
Shelf life too
Duane Benson   9/9/2013 10:39:35 AM
NO RATINGS
Another consideration is the handling of components before soldering. Everything has a shelf life. Sometimes it will be documented and sometimes not. This holds for components, PC boards and the materials used to join them.

Parts and PC boards absorb moisture over time and the metal surfaces collect impurities or react to impurities over time. Boards and parts can be baked to mitigate the moisture issue, but sometimes the only solution for old parts is to discard them.

Silver finish PC boards are great when fresh, but can and will tarnish over time, especially if not stored properly (sealed in a cool, dark place). PCB manufacturers tend to say that silver boards don't tarnish, but empirical evidence says that they do.

ENIG (electroless nickle immersion gold) is a great surface, but can be degraded too. I've seen fingerprints etched into a component land on gold boards.

Part leads can oxidize, collect dust or react to contaminants in the air. And, of course, rework is best prevented before it's needed. As Jim says, each heat cycle takes a toll on the component and PCB.

jimatems
User Rank
Rookie
Why Engineers Must Understand Soldering
jimatems   9/8/2013 1:43:36 PM
NO RATINGS
Engineers may not perform much actual soldering but they do choose the fluxes and component surfaces that the actual soldering personnel must use. Engineers evaluate the performance of soldering personnel. Engineers lay out the assemblies. Most soldering problems begin with engineers who don't understand the consequences of their actions. That's why engineers need to understand soldering.

Jim Smith
President
Electronics Manufacturing Sciences, Inc.
www.emsciences.com

Luka_J
User Rank
Rookie
What soldering?
Luka_J   9/3/2013 1:40:00 AM
NO RATINGS
I graduated electrical engineering in 2011. In all my 5 years of study they never showed or mentioned soldering. Luckily I got some practical soldering skills during my high school years and got a good mentor once I started working.

After reading this article I think I should inform myself more about soldering.

Max The Magnificent
User Rank
Blogger
Re: at what point do we stop teaching everything from the beginning?
Max The Magnificent   8/27/2013 10:24:23 AM
NO RATINGS
@Caleb: yes max, and that someone is named google!

LOL

Max The Magnificent
User Rank
Blogger
Re: How to teach
Max The Magnificent   8/27/2013 10:19:18 AM
NO RATINGS
@Janine: Of course, http://www.youtube.com/watch?v=USw_vRlRx5M is a classic also!

Max The Magnificent
User Rank
Blogger
Re: How to teach
Max The Magnificent   8/27/2013 10:17:39 AM
NO RATINGS
Caleb Kraft
User Rank
Blogger
Re: at what point do we stop teaching everything from the beginning?
Caleb Kraft   8/27/2013 10:15:55 AM
NO RATINGS
yes max, and that someone is named google!

Page 1 / 3   >   >>


Flash Poll
Top Comments of the Week
Like Us on Facebook
EE Times on Twitter
EE Times Twitter Feed

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
EE Life
Frankenstein's Fix, Teardowns, Sideshows, Design Contests, Reader Content & More
Max Maxfield

Vetinari Clock: Decisions, Decisions, Decisions …
Max Maxfield
22 comments
Things are bouncing merrily along with regard to my uber-cool Vetinari Clock project. The wooden cabinet is being handcrafted by my chum Bob (a master carpenter) using an amazing ...

Jolt Judges and Andrew Binstock

Jolt Awards: The Best Books
Jolt Judges and Andrew Binstock
1 Comment
As we do every year, Dr. Dobb's recognizes the best books of the last 12 months via the Jolt Awards -- our cycle of product awards given out every two months in each of six categories. No ...

Engineering Investigations

Air Conditioner Falls From Window, Still Works
Engineering Investigations
2 comments
It's autumn in New England. The leaves are turning to red, orange, and gold, my roses are in their second bloom, and it's time to remove the air conditioner from the window. On September ...

David Blaza

The Other Tesla
David Blaza
5 comments
I find myself going to Kickstarter and Indiegogo on a regular basis these days because they have become real innovation marketplaces. As far as I'm concerned, this is where a lot of cool ...