Breaking News
Comments
Newest First | Oldest First | Threaded View
David Ashton
User Rank
Author
Re: ATX PSU as benchtop PSU
David Ashton   8/28/2013 11:24:30 PM
NO RATINGS
@przem its more a case of, as you say, the feedback loop only being on one of the outputs so the other outputs' regulation for changing loads on them is not that good.  If you're needing spot-on voltages you need something better anyway.  Usually I've found that while the 5V is spot on, the 12V can be anything from 11 to 13 V, but it's usually good enough for testing anything that wants 12V.

The author Ben Jordan makes this point in his article:

I have seen others converting ATX power supplies to benchtop lab supplies and putting minimum load resistors in them – in my experience this is not necessary since the cooling fan is generally enough of a minimum load, and most modern switching power supplies are designed to run down to zero load anyway.

przem
User Rank
Author
Re: ATX PSU as benchtop PSU
przem   8/28/2013 9:50:05 PM
NO RATINGS
Many ATX PS designs require some loading on one of the outputs, most often 5V. Usually a 100 Ohm 1/4W resistor should suffice as a standby load. The feedback loop is usually from just one of the outputs, usually also 5V, so other voltages are usually ratiometric to 5V; I have never seen 12V drifting off while 5V is solid.

Caleb Kraft
User Rank
Author
Re: ATX PSU as benchtop PSU
Caleb Kraft   8/28/2013 6:00:31 PM
NO RATINGS
I'm wondering if more modern PSUs handle this better. I honestly haven't run into this problem at all, but like I said, I'm generally running very forgiving LED strips, as long as you don't push over 6v to them they'll survive.

David Ashton
User Rank
Author
Re: ATX PSU as benchtop PSU
David Ashton   8/28/2013 5:48:44 PM
NO RATINGS
Most supplies I find are not toooo fussy about loading as long as you are not too fussy about voltages....if you are loading the 5V but not the 12V the 12V line may be a little high.  But most supplies are surprisingly good about it, considering the conventional wisdom that switch mode PSUs need a minimum load.  Small light bulbs make good base loads and you can use one as a "power on" light.

Caleb Kraft
User Rank
Author
Re: ATX PSU as benchtop PSU
Caleb Kraft   8/28/2013 3:38:54 PM
NO RATINGS
That is a good point. I haven't run in to that myself, running LED strips usually, but I haven't used a ton of supplies either. 

ttt3
User Rank
Author
Re: ATX PSU as benchtop PSU
ttt3   8/28/2013 3:28:07 PM
NO RATINGS
Keep in mind that many ATX supplies have cross loading requirements.  If those requirements are not met, the supply becomes unstable or simply switches off.  For example, on many supplies you can't draw a lot of current on +5VV and have no load on +12V, or can't draw significant load on +3.3V without having some load on +12V and +5V, etc.  This varies greatly on the particular supply - some more expensive supplies have no dependencies at all.  I believe the cross loading requirement is related to the fact that many cheaper ATX supplies use a single transformer inside to generate 12V and 5V. 

 

Would be nice if this adapter had "dummy" load resistors incorporated to keep a minimum load on each rail.

Caleb Kraft
User Rank
Author
Re: ATX PSU as benchtop PSU
Caleb Kraft   8/28/2013 10:29:02 AM
NO RATINGS
Not only that, but they're often free when a computer dies. It is rarely the power supply. I've picked up several at garage sales and from friends.

David Ashton
User Rank
Author
ATX PSU as benchtop PSU
David Ashton   8/27/2013 11:41:35 PM
NO RATINGS
Ben Jordan had this published in Elektor magazine in June.  It is a really useful project.  An ATX supply gives a wide range of outputs and more than enough current for most purposes. 



Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Radio
NEXT UPCOMING BROADCAST

What are the engineering and design challenges in creating successful IoT devices? These devices are usually small, resource-constrained electronics designed to sense, collect, send, and/or interpret data. Some of the devices need to be smart enough to act upon data in real time, 24/7. Are the design challenges the same as with embedded systems, but with a little developer- and IT-skills added in? What do engineers need to know? Rick Merritt talks with two experts about the tools and best options for designing IoT devices in 2016. Specifically the guests will discuss sensors, security, and lessons from IoT deployments.
Like Us on Facebook
Special Video Section
LED lighting is an important feature in today’s and future ...
05:27
The LT8602 has two high voltage buck regulators with an ...
05:18
The quality and reliability of Mill-Max's two-piece ...
01:34
Why the multicopter? It has every thing in it. 58 of ...
Security is important in all parts of the IoT chain, ...
Infineon explains their philosophy and why the multicopter ...
The LTC4282 Hot SwapTM controller allows a board to be ...
This video highlights the Zynq® UltraScale+™ MPSoC, and sho...
Homeowners may soon be able to store the energy generated ...
The LTC®6363 is a low power, low noise, fully differential ...
See the Virtex® UltraScale+™ FPGA with 32.75G backplane ...
Vincent Ching, applications engineer at Avago Technologies, ...
The LT®6375 is a unity-gain difference amplifier which ...
The LTC®4015 is a complete synchronous buck controller/ ...
10:35
The LTC®2983 measures a wide variety of temperature sensors ...
The LTC®3886 is a dual PolyPhase DC/DC synchronous ...
The LTC®2348-18 is an 18-bit, low noise 8-channel ...
The LT®3042 is a high performance low dropout linear ...