Design Con 2015
Breaking News
Comments
Newest First | Oldest First | Threaded View
<<   <   Page 14 / 14
Max The Magnificent
User Rank
Blogger
But what about...?
Max The Magnificent   9/5/2013 11:19:53 AM
NO RATINGS
Right at the top of the list you need to purchase a set of tools like screwdrivers, wire cutters, wire stripper, etc.

But would you buy these independently or as a kit -- and if as a kit, which one would you recommend?

Aeroengineer
User Rank
Blogger
Re: Mistakes, I've made a few...
Aeroengineer   9/5/2013 11:19:44 AM
NO RATINGS
Yeah, I tried to put them in the proper order of how I should have done it.

 

The point you bring us is also interesting, especially with many of the newer DSO scopes offering some form of logic analyzer add-ons.  I think that there is recognition that there is a need to get more from your tools.  This is one of the reasons that I like the Red Pitaya concept.  I am really on the fence about getting that one.  It would replicate some of the tools that I already have, and not quite get me what I want for the DSO.  I would get the AWG, though, which I do not currently have.  Tempting, very tempting.

Max The Magnificent
User Rank
Blogger
Re: Mistakes, I've made a few...
Max The Magnificent   9/5/2013 11:16:31 AM
NO RATINGS
@DocDivakar: One thing I would recommend to add would be a microscope -for starters a Dino Lite or equivalent that plugs into USB.

Good suggestion -- in fact it will be interesting to see what everyone else comes up with here.

 

Aeroengineer
User Rank
Blogger
Re: #1: Location
Aeroengineer   9/5/2013 11:15:40 AM
NO RATINGS
Yes, there is a very nice Harbor Freight toolbox that I have at home for my mechanical tools.  It also houses some of the tools for my two lathes.  The only problem is that my garage is about 50' away from my house, and I am not especially motivated to go out during the winter time to get what I need.

 

As to working on the kitchen table, yes I did that for quite some time as well.  It was always such a pain when I needed to take everything into a room when we would have guests over.  I have a very wonderful wife that indulges me with my projects.  I try not to take too much advantage of it.

Max The Magnificent
User Rank
Blogger
Re: Mistakes, I've made a few...
Max The Magnificent   9/5/2013 11:14:33 AM
NO RATINGS
@Aeroengineer (a.k.a. Adam): Another mistake that I made (though some might argue that it would not be a mistake for them) was getting the oscilloscope before the logic analyzer.

Ah ... from your blog it appeared as though you purchased the logic analyzer first. In reality thsi is a tricky one -- as you say, different people would argue for one of the other ... this question might form an interesting discussion in its own right...

 

docdivakar
User Rank
CEO
Re: Mistakes, I've made a few...
docdivakar   9/5/2013 11:14:08 AM
NO RATINGS
@Max: I have to second that... this is a refreshing column, much appreciated by a fellow mechanical engineer like myself!

One thing I would recommend to add would be a microscope -for starters a Dino Lite or equivalent that plugs into USB. For a few hundred dollars, one can also get a old-fashioned benchtop steroscope that comes in handy for many things.

MP Divakar

Aeroengineer
User Rank
Blogger
Re: Mistakes, I've made a few...
Aeroengineer   9/5/2013 11:07:28 AM
NO RATINGS
You got me, I only shared one mistake, though not explicitly.  I will elaborate.  For quite some time, I never had a dedicated space for my tools and projects.  This meant that frequently tools would get misplaced, and sometimes completely lost.  Thankfully, these were small things like jumper wires, tweezers, and misc parts.  Though it would probably be fair to say that I have lost at least ~$100 of small odds and ends over the years.

 

Another mistake that I made (though some might argue that it would not be a mistake for them) was getting the oscilloscope before the logic analyzer.  I fought many hours with a few projects before I knew what a logic analyzer was.  I had the oscilloscope, but it was nowhere near as useful as the logic analyzer was to me in debugging some of these problems. 

Max The Magnificent
User Rank
Blogger
#1: Location
Max The Magnificent   9/5/2013 10:48:48 AM
NO RATINGS
@Adam: A location: I would recommend first finding a place where you can put all your tools in a somewhat organized fashion.

I agree -- this is what I lack at home -- I do most of my electronic projects on the kitchen table -- I do have a corner of the garage for my pottery stuff -- but it's all crammed together -- when I want to do anything I have to spend 30 minutes sorting everything out.

One thing I do have is one of those rolling tool boxes with lots of dwawers in the garage (my wife bought it for me for Christmas) -- that's great for storing all my tools in one place -- as you say, before that, whenever I wanted to do anything I had to waste a lot of time trying to track down the appropriate tools.

Max The Magnificent
User Rank
Blogger
Mistakes, I've made a few...
Max The Magnificent   9/5/2013 10:44:09 AM
NO RATINGS
Hi Adam -- thanks for a great column -- you started off by saying you would be "sharing some of the mistakes I've made along the way" ... but I didn't see any further reference to this...

<<   <   Page 14 / 14


Top Comments of the Week
Flash Poll
Like Us on Facebook

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
EE Life
Frankenstein's Fix, Teardowns, Sideshows, Design Contests, Reader Content & More
Max Maxfield

Want a Voltera Desktop PCB Printer?
Max Maxfield
13 comments
I just received an email from my chum Javi in Spain. "Have you heard about Voltera (VolteraInc.com)? It's a Canadian company that is going to offer desktop-size PCB printers for fast ...

Aubrey Kagan

Have You Ever Been Blindsided by Your Own Design?
Aubrey Kagan
37 comments
I recently read GCHQ: The uncensored story of Britain's most sensitive intelligence agency by Richard J. Aldrich. The Government Communication Headquarters (GCHQ), Britain's equivalent of ...

Martin Rowe

No 2014 Punkin Chunkin, What Will You Do?
Martin Rowe
2 comments
American Thanksgiving is next week, and while some people watch (American) football all day, the real competition on TV has become Punkin Chunkin. But there will be no Punkin Chunkin on TV ...

Rich Quinnell

Making the Grade in Industrial Design
Rich Quinnell
15 comments
As every developer knows, there are the paper specifications for a product design, and then there are the real requirements. The paper specs are dry, bland, and rigidly numeric, making ...

Special Video Section
The LT8640 is a 42V, 5A synchronous step-down regulator ...
The LTC2000 high-speed DAC has low noise and excellent ...
How do you protect the load and ensure output continues to ...
General-purpose DACs have applications in instrumentation, ...
Linear Technology demonstrates its latest measurement ...
10:29
Demos from Maxim Integrated at Electronica 2014 show ...
Bosch CEO Stefan Finkbeiner shows off latest combo and ...
STMicroelectronics demoed this simple gesture control ...
Keysight shows you what signals lurk in real-time at 510MHz ...
TE Connectivity's clear-plastic, full-size model car shows ...
Why culture makes Linear Tech a winner.
Recently formed Architects of Modern Power consortium ...
Specially modified Corvette C7 Stingray responds to ex Indy ...
Avago’s ACPL-K30T is the first solid-state driver qualified ...
NXP launches its line of multi-gate, multifunction, ...
Doug Bailey, VP of marketing at Power Integrations, gives a ...
See how to ease software bring-up with DesignWare IP ...
DesignWare IP Prototyping Kits enable fast software ...
This video explores the LT3086, a new member of our LDO+ ...
In today’s modern electronic systems, the need for power ...