Breaking News
Comments
Newest First | Oldest First | Threaded View
<<   <   Page 12 / 14   >   >>
toddkrein
User Rank
Rookie
Re: But what about...? -- Buy quality tools, not a set
toddkrein   9/5/2013 4:32:41 PM
NO RATINGS
I use Harbour Freight stuff as a test/filter. If I'm not sure how much I'll use something, or which item in a set I'll use, then I find them ideal.

For example, I bought a set of 20+ router bits from them for something like $20. I wore one of them out, and went out and bought a Freid version of that one bit for $17. But I wouldn't have known at the time which one(s) I would end up using.

Likewise, I bought a couple of woodworking tools. They weren't great quality, but several of them I never used, and one I deteremined had to be the highest quality I could afford. Again, let me get hands on before I pay a lot of money.

Now, soldering irons, and fine-tip tools: Buy the best you can afford.

 

Aeroengineer
User Rank
Blogger
Re: But what about...? -- Buy quality tools, not a set
Aeroengineer   9/5/2013 4:04:58 PM
NO RATINGS
Tony,

 

I agree about what you say with regards to quality.  There are very few things that I would recommend from Harbor Freight.  This workbench and the tool chest that you mentioned.  I am also fine with hammers and pry bar/chisel/I mean screwdrivers.  Their stands for grinders are not that bad.  

Though anytime I have gone there because I need an emergency tool, or a one time use tool and they ask me if I would like to purchase the extended warranty, I always laugh, and respond, "I came here knowing that I was purchasing a cheap piece of tooling that will probably break, and I am ok with that, if I wanted something with a warranty, I would go somewhere else."  The cashiers always give me a look of shock and disgust. 

TonyTib
User Rank
CEO
Re: But what about...? -- Buy quality tools, not a set
TonyTib   9/5/2013 3:23:00 PM
NO RATINGS
For the tools you use all the time, buy very good quality.  I'm in automation, so I do a lot of electro-mechanical work. 

I recommend Bondhus for hex wrenches (mine are ~15 years old), and Wiha for screwdrivers (I use mine all the time, although there are other good brands).  Invest in a good set of wire strippers; mine are Paladin with soft grips.

I use a lot of Plano 3750 tackle boxes to store stuff like connectors, pins, hoods, etc, with some of the dividers glued down.  I find Sterilte 1723 pencil boxes (available at Walmart for ~$1) great for holding stuff bulker items, and use clear plastic shoe boxes (also ~$1) for even bulkier items.

I'd go for an oscilloscope before a logic analyzer, but it depends on what you're doing.

Harbor Freight's stuff varies.  Their hand tools are, in general, junk, but if you're only going to use something occasionally then it's not worth spending a lot of money.  I've heard great things about their car jacks, and their red tool chests look nice, but I wouldn't take the cheap ones if they were free.  I've been happy with their oscillating multitool (<$20 on sale; anything better is going to be >$80), and $40 DMM (you can buy the same DMM for 2x the price; it's got some nice features such as 4000 counts and AAA batteries - I HATE 9V batteries!!!)

 

Max The Magnificent
User Rank
Blogger
#7 Logic Analyzer / #8 Oscilloscope
Max The Magnificent   9/5/2013 2:18:55 PM
NO RATINGS
I think deciding which of these to get first will spark an interesting debate.

Some of the latest and greatest machines from folks like Tektronix are small and incredibly powerful -- but they aren't cheap.

I also like the look of the Red Pitaya stuff

I've also got the Oscium iPad-based Oscilloscope and Logic Analyzer (click here for more details)

Max The Magnificent
User Rank
Blogger
Re: #4: A breadboard
Max The Magnificent   9/5/2013 2:13:19 PM
NO RATINGS
@Aeroengineer: So, I am still curious as to what the final result will be.

Oh, sorry -- this was an early incarnation of the control system for my Man vs. Woman Display-O-Meter project using a PICAXE microcontroller -- I was using a lot of shift registers to read in the values from a bunch of switches and to control a bunch of tri-colored LEDs.

Now its' just a piece of "Electronic Art" sitting on the book shelves in my office

 

Aeroengineer
User Rank
Blogger
Re: #5: A soldering iron:
Aeroengineer   9/5/2013 2:11:51 PM
NO RATINGS
That is true, but even for things that I do not know their temperatures, or that my box may not be completely accurate in its temperatures it displays, I usually have a procedure. 

 

For these, I usually start at a low temperature, then keep increasing the temp by 10°C till I get to the point that it is just barely melting the solder.  I then add another 10°C after I reach that point.  This way I keep the temp as low as possible.  There are times that if I am soldering a joint that can sink a lot of heat that I might have to turn it up more.

Aeroengineer
User Rank
Blogger
Re: #4: A breadboard
Aeroengineer   9/5/2013 2:07:37 PM
NO RATINGS
So, I am still curious as to what the final result will be.

Max The Magnificent
User Rank
Blogger
#5: A soldering iron:
Max The Magnificent   9/5/2013 1:42:18 PM
NO RATINGS
@Aeroengineer: I am not talking about one of those $10 Radio Shack "fire starters," but a real, temperature-controlled soldering iron.

Especially useful if you knwo what temperatures to use for different things. Funnily enough I picked up a nice temperature-controlled iron a couple of weeks ago at the Huntsville Hamfest for only $85

Max The Magnificent
User Rank
Blogger
Re: #4: A breadboard
Max The Magnificent   9/5/2013 1:11:27 PM
NO RATINGS
@Aeroengineer: It looks very interesting, also very well laid out with the jumper wires.

Why thank you. I love electronics -- and I love the colors of the wires and different components -- I sort of try to make my "pieces" look a bit artistic :-)

Max The Magnificent
User Rank
Blogger
Re: #4: A breadboard
Max The Magnificent   9/5/2013 1:10:09 PM
NO RATINGS
@Aeroengineer: What is that you are building?  I am guessing from the link title that it is an ADC made from discrete components.

Actually, the "adc" part of the title is based on your name ("ad" for adam) -- I just took thsi photo of the board in my office.

<<   <   Page 12 / 14   >   >>


Flash Poll
Top Comments of the Week
Like Us on Facebook
EE Times on Twitter
EE Times Twitter Feed

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
EE Life
Frankenstein's Fix, Teardowns, Sideshows, Design Contests, Reader Content & More
Max Maxfield

Feast Your Orbs on My Jiggly Exercise Machine
Max Maxfield
50 comments
Last weekend, I was chatting with my mother on the phone. She's all excited that I'm coming over to visit for a week in November. "I'll be seeing you in only seven weeks," she trilled ...

latest comment kfield Toy....or agony? :-)
Glen Chenier

Missing Datasheet Details Can Cause Problems
Glen Chenier
3 comments
It is often said that "the devil is in the details." All too often those details are hidden deep within a datasheet, where you can easily overlook them. When a datasheet reference circuit ...

David Blaza

RadioShack: The End Is Nigh!
David Blaza
123 comments
I'm feeling a little nostalgic today as I read about what looks like the imminent demise of RadioShack, at least as we currently know it. An old ubiquitous cartoon image popped into my ...

Larry Desjardin

Engineers Should Study Finance: 5 Reasons Why
Larry Desjardin
47 comments
I'm a big proponent of engineers learning financial basics. Why? Because engineers are making decisions all the time, in multiple ways. Having a good financial understanding guides these ...