Most HDLs that have been proposed are like Chisel and C~: registers are explicit, and events such as clock edges are implicit.
Notable exceptions are Verilog and VHDL. These HDLs follow the event-driven paradigm: registers are implicit and events are explicit.
Would-be HDL language designers seem to ignore this historical lesson systematically. The HDL language winners are the exception, and all those other HDLs are all but forgotten.
Why is that? Because the event-driven paradigm is much more expressive for modeling and better suited to verification (which is much harder than design itself). This is what the market wants and needs, not the focus on "full synthesizability" or "generating hardware".
In addition to SystemC, there is one more exception that I know of: MyHDL. MyHDL proudly follows the event-driven paradigm, like Verilog and VHDL. Of all the newer HDLs that have been proposed, it is the only one afaik.
Two basic reasons: (1) Hardware designers are reluctanct to move from HDL to C -- even to hardware-friendly SystemC, and (2) The productivity gains of HLS only apply to DSP-oriented designs -- number crunchers. Try designing a complex state machine or a serial comm interface with HLS. Yes, it can be done, but by the time it is done, the designer wonders exactly what the point of that exercise was.
yes these are big questions, we look forward to customers' reactions! Graphical design is a tough question, too. We already know it's not perfect for every use case in its current form, that said if done well graphical can be awesome. Anyway, it is already a huge improvement over how VHDL/Verilog/SystemC do it!
What we're saying is that software engineers may well get interested in designing hardware, but if they do they should not expect to dump a piece of C and expect the best hardware there is (HLS had promised that, I already blogged about why it will never be able to do that). However, if software engineers do get into hardware design and want a high quality of results, they would definitely go a lot faster with C~ than if they had to use VHDL/Verilog.
yes I'm aware of Chisel, I included it in my post on Synflow's blog Beyond RTL part 2: Domain-Specific Languages. I think Chisel is a good idea, like MyHDL and similar efforts. It has the advantage of being open-source, but being open or close source, or free or not, does not seem to have made a big difference in EDA historically.
Now back to Chisel, it is a bit like SystemC in that it is based on an existing, large, complex language (Scala is much better than C++, but it is far from being simple). Is the designer really free from having to deal with the Scala layer? Then it's a matter of taste, but I find Chisel's syntax complicated, and its semantics difficult to understand ('when' and 'unless' to do if/then/else but in a slightly different way).
the major difference is that C~ is a programming language dedicated for hardware, contrary to C/C++, which are software languages. Try translating 'malloc' or 'new' to hardware ^^ SystemC is somewhere in the middle, but I think it is not the solution.
C~ is above RTL, as it does not have an explicit clock, reset, or signals. The language is still cycle-accurate, so it's lower level than the code you would typically write with HLS. So it's kind of in-the-middle, we use a model of computation derived from dataflow process networks, which define computations in terms of action firings; in C~ a firing is executed in a cycle.
As I explained in the post I linked to above, extending C++ is probably not a good idea, it is difficult to parse, complicated to analyze, and you still have to deal with the C++ layer (hello ugly error messages).
I agree there has been a reluctance to move up to higher levels of abstraction but it is partly because HLS does not really work. Is definitely not sufficiently automated.
So you end up modeling at high-level and then designing at lower level and then spending a lot of effort to try and be confident that what you modeled at high level is equivalent to what you are designing at lower level.
And why has HLS not worked?
Here is my argument.
Because unlike RTL-to-gate-level -- where designers were willing to give up messing about with transistors and gates and dimensions of cells -- there was no obvious way to accept constraints (even at the IP core level).
And that has happened because there is not equivalent to the NAND completeness of logic at the gate level. Isn't it DeMorgan's Theorems that prove that all logic systems can be converted into NAND gates or NOR gates? Therefore being constained to using a limited set of gates allow all digital logic to be created. The constraint of using those predetermined gates allows synthesis to work.
There is no equivalent limited set of IP cores that could create all-imaginable logic circuits and so engineers are reluctant to accept any constraints on either IP cores or their dimensions and no obvious way to guide a synthesis engine.
Until we have automated provable synthesis of yet unimagined logic EDA is stuck working at multiple levels of abstraction and stuggling to prove their equivalence.
I see three factors that might afflict Synflow but I think you are right to highlight the language issue. Proprietary languages often struggle for adoption.
The question has to be how does C~ compare with such offerings as SystemVerilog and perhaps to a lesser degree SystemC...but also how the IDE can connect with descriptions in those languages.
A second factor is graphical design. Textual languages have dominated the IC design area for decades, despite one or previous attempts to introduce graphical design front-ends that failed to gain traction.
A third factor is Synflow's avowed intent to steer clear of software. This is a bit of double-edged sword. On the one hand they are probably right that there are two distinct audiences. One is system/software developers who are not interested in hardware.The second is hardware engineers. However, high-level hardware engineers for a long time had to have an eye on the software. Often they are choosing whether something should be software programmable or accelerated in hardware.
So there are fundamental questions to be addressed but all could be resolved in Synflow's favor if this tool produces high QoR designs in a fraction of the time of conventional design AND it could pass designs over to an SoC RTL to gate-level desgn process.
It looks very appealing for small to medium projects in companies thats can't afford big tool chains from synopsys or others. Is the simulator included ? Is it possible to simulate mixed design with C~ top level and some VHDL/Verilog IPs ? What about cosimulation ?
What are the engineering and design challenges in creating successful IoT devices? These devices are usually small, resource-constrained electronics designed to sense, collect, send, and/or interpret data. Some of the devices need to be smart enough to act upon data in real time, 24/7. Specifically the guests will discuss sensors, security, and lessons from IoT deployments.