Breaking News
Comments
Newest First | Oldest First | Threaded View
<<   <   Page 2 / 2
rick merritt
User Rank
Author
Re: LOCSOI
rick merritt   10/10/2013 3:49:14 AM
NO RATINGS
@Resistion" Good question, but I don't have a good answer. I'l ask An to weigh in

resistion
User Rank
Author
Re: An's being generous to EUV
resistion   10/9/2013 10:55:44 PM
NO RATINGS
"Immersion systems may need 22 masks at 10nm, up from ten at 28nm, essentially using costly triple patterning in a handful of layers and double patterning at all others. EUV could cut that down to ten masks at 10nm, researchers estimate."

So, again confirming, essentially just one node (10 nm) for EUV single patterning. Same situation faced 157 nm, with far less drastic infrastructure changes required.

resistion
User Rank
Author
memory part
resistion   10/9/2013 10:29:41 PM
NO RATINGS
For the memory portion, I was a bit surprised that there was not more focus on vertical NAND or future vertical 3D-NVM. That technology has just recently been announced, while FinFETs have been around much longer.

Also, why so much focus on STT-MRAM? They should know it is quite a fragile device. More fragile than a transistor at leading edge. The read is not 100% non-destructive, for the spec that is expected (quadrillion times).

AKH0
User Rank
Author
14nm FDSOI
AKH0   10/9/2013 7:00:57 PM
NO RATINGS
To be clear, IMEC never really worked on 14nm FDSOI. This was developed by IBM-ST-Leti alliance. So, it really doen't mean anything if its is shown on IMEC's roadmap or not.

resistion
User Rank
Author
LOCSOI
resistion   10/9/2013 5:47:26 PM
NO RATINGS
7 nm shows LOCSOI - is that local SOI?

resistion
User Rank
Author
An's being generous to EUV
resistion   10/9/2013 8:02:08 AM
NO RATINGS
I watched/listened to a video interview in the past year given by Debra Vogler, in that interview An gave enough reasons to show why EUV is basically "out there" forever, saving my efforts. Dragging N10 and N7 nodes to a decade or longer, is "out there" forever.

<<   <   Page 2 / 2


Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Radio
LATEST ARCHIVED BROADCAST

What are the engineering and design challenges in creating successful IoT devices? These devices are usually small, resource-constrained electronics designed to sense, collect, send, and/or interpret data. Some of the devices need to be smart enough to act upon data in real time, 24/7. Specifically the guests will discuss sensors, security, and lessons from IoT deployments.

Brought to you by:

Like Us on Facebook
Special Video Section
The LTC3649 step-down regulator combines key features of a ...
Once the base layer of a design has been taped out, making ...
In this short video we show an LED light demo to ...
The LTC2380-24 is a versatile 24-bit SAR ADC that combines ...
In this short video we show an LED light demo to ...
02:46
Wireless Power enables applications where it is difficult ...
07:41
LEDs are being used in current luxury model automotive ...
With design sizes expected to increase by 5X through 2020, ...
01:48
Linear Technology’s LT8330 and LT8331, two Low Quiescent ...
The quality and reliability of Mill-Max's two-piece ...
LED lighting is an important feature in today’s and future ...
05:27
The LT8602 has two high voltage buck regulators with an ...
05:18
Silego Technology’s highly versatile Mixed-signal GreenPAK ...
The quality and reliability of Mill-Max's two-piece ...
01:34
Why the multicopter? It has every thing in it. 58 of ...
Security is important in all parts of the IoT chain, ...
Infineon explains their philosophy and why the multicopter ...
The LTC4282 Hot SwapTM controller allows a board to be ...
This video highlights the Zynq® UltraScale+™ MPSoC, and sho...
Homeowners may soon be able to store the energy generated ...