Breaking News
Comments
Newest First | Oldest First | Threaded View
<<   <   Page 3 / 4   >   >>
Duane Benson
User Rank
Blogger
Very interesting article
Duane Benson   10/17/2013 7:19:25 PM
NO RATINGS
David - I've used the black tape and pen from Radio Shack, but never a Vero board. I didn't have much luck etching the PCBs though, so I tended to fall back to wire-wrap or proto-board.

These days, we're kind of in a golden age or tools and suppliers. I'm contstantly amazed at how much we can do these days, with free or inexpensive tools. Not to mention, the wealth of information at our dispoal.

Back in the 1980's, I tried to design a Caller-ID system. The phone company had just started sending the information down the phone line prior to the ring signal, so it was possible, but no one was selling the things yet. It proabbly took me six months or more of searching, calling, ordering documents & repeat before I found enough documentation to get close. The same would probably take me about 20 minutes now.

zeeglen
User Rank
Blogger
Re: Ferric Chloride
zeeglen   10/17/2013 12:42:45 AM
NO RATINGS
The wierd thing was that I had never made that dumb mistake when changing the oil in my car.

David Ashton
User Rank
Blogger
Re: Ferric Chloride
David Ashton   10/16/2013 9:02:11 PM
NO RATINGS
@Zeeglen - even when it's not my vile HCl / FeCl3 mix, it's certainly not stuff you want to chuck around the place.  I've often thought, when I'm sloshing a PCB back and forth in an old icecream container, that I must make a bubble etcher - like a thin aquarium tank with a tube with holes at the bottom connected to an aquarium pump to blow bubbles thru the liquid to agitate it.  Maybe a heater as well....   Then I don't make another board for a couple of months and the idea vanishes till the next time.....

zeeglen
User Rank
Blogger
Re: Ferric Chloride
zeeglen   10/16/2013 8:33:00 PM
NO RATINGS
Back in college a couple of us students had summer internships, one day we were assigned the task of servicing the PCB etching machine.  This was a small tub on wheels that used a magnetically-coupled impeller to slosh the feric chloride around while the pcb remained stationary.  I forget whether it was just a cleaning or if we had to replace the pump impeller, but whatever it was necessary to first remove the ferric chloride.

We undid the drain on the tub and collected the ferric chloride in a plastic bucket.  After we finished servicing the system I started pouring the ferric chloride back in.  About a quarter-bucket later I suddenly remembered - "The drain plug!"  Was quite a mess and took a lot of paper towels, but the tray shelf in the bottom of the cart caught most of it.  Fortunately none of the profs noticed.

David Ashton
User Rank
Blogger
Re: Me too!
David Ashton   10/16/2013 6:22:28 PM
NO RATINGS
@antedeluvian  Hi Aubrey....I did read and comment on your How it Was on the subject.  You certainly got a lot further with the computerised stuff than I have - I gotta learn one of the tools soon.   Watching the track pattern come out on the board as you develop it always gives me a thrill - like developing your own photos did.  Your descriptions of waiting an hour for the display to pan are a graphic reminder of how PC performance used to lag behind software requirements in the old days - though that seems to be a problem still, I doubt users these days would wait an hour!

David Ashton
User Rank
Blogger
Re: Ferric Chloride
David Ashton   10/16/2013 6:12:12 PM
NO RATINGS
@Karen I quite enjoyed Chemistry at school and had a couple of chemistry sets at home too.  Of course these days the chem sets (and the teaching at school) are pretty tame.  I remember our chem teacher at school would not let us see what happened when sodium reacted with water.  So my friends and I hatched a plot...we stole some sodium from the lab, I carried it home in my pocket wrapped in oily tissue in a plastic bag (It was kept under oil in the lab as it reacts with air).  At home we chucked it in our swimming pool.  It rose to the surface, bubbling furiously and then exploded.  To this day I get cold shivers wondering what would have happened had it started combusting in my pocket.

antedeluvian
User Rank
Blogger
Me too!
antedeluvian   10/16/2013 10:28:48 AM
NO RATINGS
David

Our progression through PCB layout tools sounds quite similar as I described in Max's How it Was series. However I never tried making my own PCBs until after university and then only once.

When you said that Rhodesia was not the centre of the electronics universe, you were understating by a long shot. In 1967/8 my electronics course was mainly valves (tubes to the the bilingually challenged) and you certainly didn't need PCBs for those. I know that I have a few years on you and I was in Bulawayo and not Salisbury, but my teachers were never of the goto variety. They were more of the talk softly (and by that I mean little content) and carry a BIG stick variety. My physics teacher even suggested that I was no good at electronics and that I should give it up. 45 years later I reflect and think maybe he was right!

kfield
User Rank
Blogger
Re: Ferric Chloride
kfield   10/16/2013 10:15:57 AM
NO RATINGS
@davidashton David, sounds like you had as much fun messing around with chemistry as you did with electronics!

Crusty1
User Rank
CEO
Re: Fritzing
Crusty1   10/16/2013 8:56:32 AM
NO RATINGS
@David :  Good thing you have a longer attention span!

Mrs Crusty thinks I do not have enough attention span for the things she thinks are important and that I have a far too permenant attention span to things electronic.

Probably enough said

David Ashton
User Rank
Blogger
Re: Fritzing
David Ashton   10/16/2013 7:42:00 AM
NO RATINGS
@Crusty...."Funny thing the link was in one of your posts."   Yeah right, I'm getting old.....if you'd said reprap I would have cottoned on.... :-)   I kinda skimmed thu the article at the time, thinking I would get back to it.  Good thing you have a longer attention span!

<<   <   Page 3 / 4   >   >>


Most Recent Comments
Steve Manley
 
engineers
 
Weapon
 
rick merritt
 
rick merritt
 
Loser99
 
Aeroengineer
 
Aeroengineer
 
Aeroengineer
EE Life
Frankenstein's Fix, Teardowns, Sideshows, Design Contests, Reader Content & More
Glen Chenier

Engineers Solve Analog/Digital Problem, Invent Creative Expletives
Glen Chenier
Post a comment
An analog engineer and a digital engineer join forces, use their respective skills, and pull a few bunnies out of a hat to troubleshoot a system with which they are completely unfamiliar. ...

Max Maxfield

What's the Best Traveling Toolkit?
Max Maxfield
13 comments
A few years ago at a family Christmas party, I won a pocket knife as part of a "Dirty Santa" game. This little scamp was a Buck 730 X-Tract. In addition to an incredibly strong and sharp ...

Rishabh N. Mahajani, High School Senior and Future Engineer

Future Engineers: Don’t 'Trip Up' on Your College Road Trip
Rishabh N. Mahajani, High School Senior and Future Engineer
10 comments
A future engineer shares his impressions of a recent tour of top schools and offers advice on making the most of the time-honored tradition of the college road trip.

Larry Desjardin

Engineers Should Study Finance: 5 Reasons Why
Larry Desjardin
41 comments
I'm a big proponent of engineers learning financial basics. Why? Because engineers are making decisions all the time, in multiple ways. Having a good financial understanding guides these ...

Top Comments of the Week
Flash Poll
Like Us on Facebook
EE Times on Twitter
EE Times Twitter Feed

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)