Embedded Systems Conference
Breaking News
Newest First | Oldest First | Threaded View
User Rank
Crashing into walls
salbayeng   11/4/2013 10:45:02 PM
The robots speed is limited in the same ways as driving a car at night is limited by the headlight range .  So you have to work out the collision avoidance sensing distance , and use this in conjunction with the braking distance to determine the maximum "safe speed" . any where above this speed and you will have a non-zero velocity when robot_to_wall_range = zero . So you don't want to be too fast or too big.

About two years back I made robot base, using mostly "agricultural materials", basically a plywood base, 2 x 10" pneumatic wheels, 2 x castors, electric scooter motors, chain drive and a 12AH battery, The encoder was optical , using the sprocket teeth on the motor. At 100% modulation it would be a fast walking pace (but we limited it to ~25%) and weighed in around 6kgs

For sensors it had a magnetic compass, infrared short range, ultrasonic for long range, and some microswitches on a bumper bar for emergency shutdown. 

The control was over a (wired) serial link using one of those Pololu M128 modules with the LCD and 5 buttons (we had UHF transceievers for later). 

The algorithm that worked best basically used the range from the ultrasonic sensor, once this was less than 1m it would make  a random left or right deviation of 10degrees , then keep going in the direction with longest range (It also remembered the best direction of the last two turns to bias the next turn direction)  . In retrospect it would have been better to have stereoscopic sensors, and just veer in the direction of longest range. Using a single sensor and trying to remember the "best range" is fraught with difficulties.  

So when it was trundling along you could step in front of it and it would go around you .  And it would avoid walls most of the time, but would occasionally sideswipe walls or furniture.   

Problem was during development it would always be crashing into walls or running over your toes, and the black rubber would leave skidmarks on the floor  and walls, and tear flesh off your toes and ankles.  And because of it's weight it would just buckle up the safety bumper and jam the microswitches.

So your little robot is probably about right with 4" wheels, small enough to nudge with your foot, light enough to bounce off walls and furniture, but big enough so you can work on it comfortably. 

User Rank
Re: Lattice IceStick arrives at Crusty Mansion
Crusty1   10/31/2013 12:04:49 PM
@Max : yes seen the sensors for Pmod, also has unpopulated 0.1 connector positions to get at even more I/O


Max The Magnificent
User Rank
Re: Lattice IceStick arrives at Crusty Mansion
Max The Magnificent   10/31/2013 11:35:06 AM
@Crusty: Just got a goody through the post today, my Lattice iCEstick evaluation kit.

Cool Beans -- have you seen all of the low-cost Pmod sensors you can get from Digilent and Analog Devuces and TI and Maxim -- these will plug into the Pmod connector on your iCEstick

User Rank
Lattice IceStick arrives at Crusty Mansion
Crusty1   10/31/2013 11:12:46 AM
@Max, David,

Just got a goody through the post today, my Lattice iCEstick evaluation kit. www.latticesemi.com/icestick

Now we are at EE Times, I presume there is no limitation to what chip maker we can talk about?

This board is so cheap I do not have to worry about blowing it up, except for getting a replacement, it took a couple of months for the order tpo arrive, hopefully stock levels in Europe are getting better.

Not sure what I will do with the beast yet, but I am certain something will come to mind.


Max The Magnificent
User Rank
Re: 40 in/s
Max The Magnificent   10/30/2013 4:10:12 PM
@David: ...your cat is not going to get any peace I think...

It's PAYBACK time!!! :-)

Max The Magnificent
User Rank
Re: size matters
Max The Magnificent   10/30/2013 4:09:35 PM
@Caleb: I see you're not going small with this one! 4 inch wheels!

I don't know what's considered big or small in this arena -- these were the smallest omni-directional wheels that I liked -- alhough there are some smaller ones out there. The thing is that once I actually have something up and running, I'll better know what direction to go in (no pun intended)

David Ashton
User Rank
40 in/s
David Ashton   10/30/2013 3:17:00 PM
40 inches a second (that's 1 m/s for us civilised folks) is a fair pace...your cat is not going to get any peace I think

Caleb Kraft
User Rank
size matters
Caleb Kraft   10/30/2013 2:05:04 PM
I see you're not going small with this one! 4 inch wheels!


NASA's Orion Flight Software Production Systems Manager Darrel G. Raines joins Planet Analog Editor Steve Taranovich and Embedded.com Editor Max Maxfield to talk about embedded flight software used in Orion Spacecraft, part of NASA's Mars mission. Live radio show and live chat. Get your questions ready.
Brought to you by

Top Comments of the Week
Like Us on Facebook

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Special Video Section
The LTC®4015 is a complete synchronous buck controller/ ...
The LTC®2983 measures a wide variety of temperature sensors ...
The LTC®3886 is a dual PolyPhase DC/DC synchronous ...
The LT®3042 is a high performance low dropout linear ...
Chwan-Jye Foo (C.J Foo), product marketing manager for ...
The LT®3752/LT3752-1 are current mode PWM controllers ...
LED lighting is an important feature in today’s and future ...
Active balancing of series connected battery stacks exists ...
After a four-year absence, Infineon returns to Mobile World ...
A laptop’s 65-watt adapter can be made 6 times smaller and ...
An industry network should have device and data security at ...
The LTC2975 is a four-channel PMBus Power System Manager ...
In this video, a new high speed CMOS output comparator ...
The LT8640 is a 42V, 5A synchronous step-down regulator ...
The LTC2000 high-speed DAC has low noise and excellent ...
How do you protect the load and ensure output continues to ...
General-purpose DACs have applications in instrumentation, ...
Linear Technology demonstrates its latest measurement ...
Demos from Maxim Integrated at Electronica 2014 show ...
Bosch CEO Stefan Finkbeiner shows off latest combo and ...