Breaking News
Comments
Newest First | Oldest First | Threaded View
_hm
User Rank
Author
Fourth dimension - talk to friends
_hm   11/2/2013 3:33:29 PM
NO RATINGS
Fourth important dimension is to talk to your friends of what you are doing and how it will work and what problems do you have. Review process and talking to some part to friends outside is also desired. Main advantage of this is self realization of mistakes. When one explain it to friend, and when he asks few questions, one self realize mistakes to be fixed or design to be enhanced. 

betajet
User Rank
Author
Re: First thing
betajet   11/1/2013 3:06:30 PM
NO RATINGS
I always do a continuity check of all power and ground pins on a bare board as soon as it's available.  This doesn't take much time, and makes sure the PC design software or the PCB manufacturer didn't miss something.  I also check the Gerbers before they go out to the PCB house.

If you have a package with a large ground pad on the bottom of the chip, expect that the assembly house will forget to solder it for the prototypes.  In many cases, that's the only ground connection for the chip.  If possible, extend the PCB artwork for the pad out from under the chip so you can heat it up with a soldering iron.

If you have programmable parts, always bring out spare I/Os to test points (vias).  These are invaluable for debugging FPGA logic in real time.

Draw your schematics as if you're going to be the one debugging the board.  Number your passive components in a sensible way so they're easy to find in the schematics -- I like to number all components in the same sequence as the pages of the schematics.  Don't use automatic numbering: the hours you saved by not numbering the components by hand will become days added to debugging.

Draw component symbols to match the package pinout.  This will make it a lot easier to debug.  For BGAs, match the pad sequence on the chip itself.  For Xilinx FPGAs, you can get this from the graphical chip editor.  For others, BSDL will probably get you the information.

Max The Magnificent
User Rank
Author
Re: First thing
Max The Magnificent   11/1/2013 8:01:58 AM
NO RATINGS
@MKolb: One of the first things I do is a detailed visual inspection and then a continuity test between the power and ground planes.

YES!!!  I do this too -- I think it's so obvious I didn't even think to mention it ... but as they say "Common sense isn;t as common as it used to be" :-)

zeeglen
User Rank
Author
Re: First thing
zeeglen   10/31/2013 3:47:13 PM
NO RATINGS
Yup, and use a current-limited lab supply and crank up the current slowly.

Adam-Taylor
User Rank
Author
Re: First thing
Adam-Taylor   10/31/2013 3:23:39 PM
NO RATINGS
Infact I recenty wrote about this in a little more detail in Xcell http://issuu.com/xcelljournal/docs/xcell_journal_issue_85

page 48 onwards

Adam-Taylor
User Rank
Author
Re: First thing
Adam-Taylor   10/31/2013 3:16:16 PM
NO RATINGS
Mkolb That is the first thing everyone should do

MKolb
User Rank
Author
First thing
MKolb   10/31/2013 3:12:35 PM
NO RATINGS
One of the first things I do is a detailed visual inspection and then a continuity test between the power and ground planes.  Nobody likes unpleasant surprizes the first time you power it up.

Max The Magnificent
User Rank
Author
Re: Freshly baked circuit boards
Max The Magnificent   10/31/2013 2:02:34 PM
NO RATINGS
@zeeglen: Throw lots of ground test points at the board...

Good one!

zeeglen
User Rank
Author
Re: Freshly baked circuit boards
zeeglen   10/31/2013 1:20:55 PM
NO RATINGS
Throw lots of ground test points at the board so that you always have one nearby when scope probing fast or low-level signals.  These do not tolerate long ground wires to the probes.  If there is room, a connector for a logic analyzer can save a lot of pain.

Max The Magnificent
User Rank
Author
Freshly baked circuit boards
Max The Magnificent   10/31/2013 12:09:55 PM
NO RATINGS
@Adam: One of the most exciting stages of an engineering project is when the hardware arrives in the lab for the first time...

Ah, I love the smell of a freshly baked circuit board first thing in the morning...



Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Radio
LATEST ARCHIVED BROADCAST

What are the engineering and design challenges in creating successful IoT devices? These devices are usually small, resource-constrained electronics designed to sense, collect, send, and/or interpret data. Some of the devices need to be smart enough to act upon data in real time, 24/7. Specifically the guests will discuss sensors, security, and lessons from IoT deployments.

Brought to you by:

Most Recent Comments
rick merritt
 
Saturation
 
DCH0
 
realjjj
 
traneus
 
realjjj
 
realjjj
 
Doug_S
 
spike_johan
Like Us on Facebook
Special Video Section
Once the base layer of a design has been taped out, making ...
In this short video we show an LED light demo to ...
The LTC2380-24 is a versatile 24-bit SAR ADC that combines ...
In this short video we show an LED light demo to ...
02:46
Wireless Power enables applications where it is difficult ...
07:41
LEDs are being used in current luxury model automotive ...
With design sizes expected to increase by 5X through 2020, ...
01:48
Linear Technology’s LT8330 and LT8331, two Low Quiescent ...
The quality and reliability of Mill-Max's two-piece ...
LED lighting is an important feature in today’s and future ...
05:27
The LT8602 has two high voltage buck regulators with an ...
05:18
Silego Technology’s highly versatile Mixed-signal GreenPAK ...
The quality and reliability of Mill-Max's two-piece ...
01:34
Why the multicopter? It has every thing in it. 58 of ...
Security is important in all parts of the IoT chain, ...
Infineon explains their philosophy and why the multicopter ...
The LTC4282 Hot SwapTM controller allows a board to be ...
This video highlights the Zynq® UltraScale+™ MPSoC, and sho...
Homeowners may soon be able to store the energy generated ...
The LTC®6363 is a low power, low noise, fully differential ...