The 34461A version page is confusing. On close read it says, Firmware/Software
My best understanding (no affiliation with Agilent) is that the current firmware version -which gets installed in the DMM- is 1.09 (listed as the base version, however, it was an upgrade for me, I think from 1.08)
Then, there is support software that installs on a computer such as a PC, http://www.home.agilent.com/en/pd-2036130-pn-E2300/command-expert-11?&cc=US&lc=eng called Command Expert, now at Ver. 1.2 Update 1
There is a recommendation to leave the 34461A on 24/7 with the screen saver enabled: http://www.home.agilent.com/owc_discussions/thread.jspa?threadID=36071&tstart=0 "With a power consumption of 10W and a screen saver (Shift - Utility - System Setup - User Settings - Display Options - Scrn Svr) that dims the display following long periods of inactivity, it is recommended the 34460A/34461A DMM continually remain powered on."
Also, from a cold start, it takes some minutes to reach internal temperature stability (e.g. the ovenized reference) for use beyond about 5 digits.
One argument might be that boot-up time is on the order of a minimum time to use a partially "warmed up" DMM below spec (before full warm-up). The 34401A and newer 34410A also used ovenized references and have the same warm up needs.
On the other hand, when at the center of the bench, many of us use the DMM at hand for 3 1/2 to 4 1/2 digit quick measurements, which take very little warm up. Also, if one is working on an ATE setup (e.g. by LabVIEW), in early programming efforts, all that is needed is the DMM to be alive and responding.
I find the GUI of the 34461A to be outstanding. Like many others, we are hoping some day for a 61A style DMM that falls somewhere between the specs of the newer 34410A (the "10A") and the now ancient, but capable 3458A.
@Joe Thanks for the pointer to the new firmware. I installed it and you're absolutely right--the boot time is noticeably shorter (24 seconds!). I hope Agilent can make it even quicker with another firmware update. I really like the 34461A, and the only complaint that I have with it is that it's not "instant on" like all of my other DMMs.
I have a 34461A, as well as a 34401A. Although the 34461A is way ahead of the 34401A in design, available functions, and the wonderful graphical display, there's one spec where the 34461A is much inferior: turn-on time. The 34401A is ready to go after three seconds of self-test, but the 34461A takes a full 55 seconds from the time I press the power switch to the time it is first usable. For an application where it will be data logging or connected to an ATE system, this probably doesn't matter, but sometimes I want to walk up to a DMM, turn it on, make a quick measurement, and be on my way. For this reason alone, I'll be keeping the 34401A.
Besides, why not have two (or more) 6-1/2 digit DMMs sitting on the bench? :-)
I've mentioned this problem to my distributor and they assure me that my comments will be passed on to Agilent. Whether it can or will be fixed is another question.
What are the engineering and design challenges in creating successful IoT devices? These devices are usually small, resource-constrained electronics designed to sense, collect, send, and/or interpret data. Some of the devices need to be smart enough to act upon data in real time, 24/7. Are the design challenges the same as with embedded systems, but with a little developer- and IT-skills added in? What do engineers need to know? Rick Merritt talks with two experts about the tools and best options for designing IoT devices in 2016. Specifically the guests will discuss sensors, security, and lessons from IoT deployments.