Embedded Systems Conference
Breaking News
Comments
Newest First | Oldest First | Threaded View
<<   <   Page 5 / 5
Graham Bell
User Rank
Author
Re: Schematic Courtesy the Museum of Broadcasting
Graham Bell   11/14/2013 7:53:09 PM
NO RATINGS
I have seen the volume filament control on other early radios.  It worked nicely on strong local stations; you could burn just enough battery power to get a decent sound to your headphones or perhaps an early loudspeaker. And with the lower gain, meant later stages were not overloaed from a strong signal.  However if you were trying to pull in a far away station, and getting the most gain out of the tubes, you would shorten your battery life.

Bert22306
User Rank
Author
Re: Schematic Courtesy the Museum of Broadcasting
Bert22306   11/14/2013 7:32:25 PM
NO RATINGS
Hey, thanks for that, Graham.

Holy smokes, it was simple. You have three consecutive transformer-coupled RF amps, each one tuned in synchronism with the other two by virtue of the mechanically ganged tuning capacitor. Then the envelope detector, nothing more than a low pass filter. Then two series connected audio amp stages. All transformer coupled, class A, no feedback, no separate voltage and current amp stage in the audio amp.

The first audio output has a high-pass filter, to cut down the squealing no doubt. They didn't like anything above 5 KHz audio in those days. And the really odd thing is the volume control. It operates on the voltage appplied to the *heaters* of the RF amps. How weird is that? As opposed to being a voltage divider just before the audio amp. I wonder if that was prevalent back then?

Susan Rambo
User Rank
Author
Re: Schematic Courtesy the Museum of Broadcasting
Susan Rambo   11/14/2013 6:47:43 PM
NO RATINGS
@Graham Bell, thanks for the Radiola schematic and link to Museum of Broadcasting.

Graham Bell
User Rank
Author
Schematic Courtesy the Museum of Broadcasting
Graham Bell   11/14/2013 6:17:11 PM
I found the schematic for the Radiola 16 at the Museum of Broadcasting .  Click on the thumbnail for a larger view.   Notice the the use of a grid-leak detetctor. Enjoy!



http://www.museumofbroadcasting.org/16schemLo.jpg

Bert22306
User Rank
Author
Electro-mechanical
Bert22306   11/14/2013 5:18:20 PM
What strikes me most is how mechanical these old radios were. From the mechanical tuning capacitor, to the tubes, to the volume control. And yes, those wood cases seemed to be meticulously built.

But on the other hand, one reason electronics were this way is because they had no options. If they had plastics, they wouldn't have used wood. If they had solid state electronics, they never would have bothered with these touchy and expensive electro-mechanical tubes. But they are fun to watch as they glow.

Those mechanical tuning capacitors could be problematic. We had an old radio where that tuning capacitor became vulnerable to the slightest vibration, emitting loud thumps, and was scratchy too. Tubes changed characteristics as they aged, or just as they warmed up with each use, were an egregious waste of energy, and were so bulky that the electronic design always had to be compromised to keep the number of tubes required in check. And so forth. These old electronics are fun to look at, but we have also come a long way.

In spite of the common wisdom, solid state electronic products can be far, far, far more long lasting than these old radios or phonographs. I'm still using an amp I built in 1980, for instance. Hard to do that with these old tube jobs. The tubes would need changing, plus the heat they emitted caused other components to fail as well.

Susan Rambo
User Rank
Author
Beautiful!
Susan Rambo   11/14/2013 4:03:25 PM
NO RATINGS
This radio is a thing of beauty! Nice shots, Caleb. Thanks for this.

<<   <   Page 5 / 5


Radio
NEXT UPCOMING BROADCAST
In conjunction with unveiling of EE Times’ Silicon 60 list, journalist & Silicon 60 researcher Peter Clarke hosts a conversation on startups in the electronics industry. One of Silicon Valley's great contributions to the world has been the demonstration of how the application of entrepreneurship and venture capital to electronics and semiconductor hardware can create wealth with developments in semiconductors, displays, design automation, MEMS and across the breadth of hardware developments. But in recent years concerns have been raised that traditional venture capital has turned its back on hardware-related startups in favor of software and Internet applications and services. Panelists from incubators join Peter Clarke in debate.
Flash Poll
Top Comments of the Week
Like Us on Facebook

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Special Video Section
Chwan-Jye Foo (C.J Foo), product marketing manager for ...
The LT®3752/LT3752-1 are current mode PWM controllers ...
LED lighting is an important feature in today’s and future ...
Active balancing of series connected battery stacks exists ...
After a four-year absence, Infineon returns to Mobile World ...
A laptop’s 65-watt adapter can be made 6 times smaller and ...
An industry network should have device and data security at ...
The LTC2975 is a four-channel PMBus Power System Manager ...
In this video, a new high speed CMOS output comparator ...
The LT8640 is a 42V, 5A synchronous step-down regulator ...
The LTC2000 high-speed DAC has low noise and excellent ...
How do you protect the load and ensure output continues to ...
General-purpose DACs have applications in instrumentation, ...
Linear Technology demonstrates its latest measurement ...
10:29
Demos from Maxim Integrated at Electronica 2014 show ...
Bosch CEO Stefan Finkbeiner shows off latest combo and ...
STMicroelectronics demoed this simple gesture control ...
Keysight shows you what signals lurk in real-time at 510MHz ...
TE Connectivity's clear-plastic, full-size model car shows ...
Why culture makes Linear Tech a winner.