Breaking News
Comments
Newest First | Oldest First | Threaded View
Page 1 / 2   >   >>
TonyTib
User Rank
Author
Re: outlet
TonyTib   11/21/2013 6:43:34 PM
NO RATINGS
Well, there's a big enough market for DIN rail outlets that at least one more company, ASI, makes them.  Another use for them is convenient outlets for devices within your machine that like standard electrical cords (such as PCs, monitors, and some power supplies) -- and DIN rail outlets are easy to mount.


One reason I use Phoenix DIN rail enclosures is that Phoenix Contact's availability is quite good through Mouser, Digikey, etc -- and we get pretty good pricing through our local distributor.

Caleb Kraft
User Rank
Author
Re: outlet
Caleb Kraft   11/21/2013 6:05:01 PM
NO RATINGS
thanks for the explanation!

antedeluvian
User Rank
Author
Re: outlet
antedeluvian   11/21/2013 6:03:29 PM
NO RATINGS
Caleb

That power outlet cracked me up! Why was taht even on a pcb?

"Ours is not to reason why..."

As near as I can tell, the reasoning goes like this:

When you have a panel (in an industrial environment)  there are times that you want a 120VAC outlet to power instrumenation. Often it is transient like when you need a 'scope for debugging. 

I have seen panels with loose extension cords inside them for that purpose, but there are issues (agency approval for one thing). So it would be nice to have the outlet mount on a DIN rail.  Also, given the environment, it is prudent to have a circuit breaker or earth leakage.I doubt that the outlet manufacturers would see enough volume to justify a different rail mounting enclosure, not to mention further agency approvals, so this became our niche.

Mounting the  outlet on a PCB so it can fit in a housing then allows it to mount on a DIN rail. Figure 6 gives you an idea of the board mounted in a housing. The board in Figure 5 actually has an enclosure that completely encases it. It also has a rail foot or screw mounting option. In addition the connection to the outlet are brought out to screw terminals on the PCB so that the power can be wired to the top side of the board after all the modules have been installed in the panel. You can see the two 3-way black connectors on the top side of Figure 5 and the 6-way orange connector in Figure 6.

Caleb Kraft
User Rank
Author
outlet
Caleb Kraft   11/21/2013 4:42:01 PM
NO RATINGS
That power outlet cracked me up! Why was taht even on a pcb?

antedeluvian
User Rank
Author
Re: DIN rail modules as an art form!
antedeluvian   11/21/2013 10:12:42 AM
NO RATINGS
salbayeng

Another neat module on DIN rail I've seen is the current sensor, It's just a current transformer and relay on the PCB,

We have done several variations of those as well- funny I didn't think to include them.

Where do you get the DK5 and DK6 housings from ?

The DK5 and DK6s have been through several manufacturing iterations but are now made exclusively by Weidmuller. I doubt that any of their distributors would know about the housing and you would have to speak to Wedimuller directly in whatever country you are. They have ben superceded by many newer housings and  I believe they are trying to discontinue them. We were Weidmuller's design facilty in Canada and were spun off. In fact we still (for the next 2 months) work out of Weidmuller's Canadian facility. We still manufacture the products that we originally designed, under licence (those devices in the photo are theirs).

(There is apparently a thicker version of the DK5 too.)

I (and the Weidmuller tech support guy downstairs) am unaware of any wider DK5 package. There was a company called Sensorpulse that made a "top hat" cover for the DK6 that would allow you to use taller components in the DK6. We did use that top hat on some designs and I think we still have stock.

I have about 20 x DK5 but can't seem to get any more

If you need a few more, I think I may be able to help- but if you are going into production you may want to reconsider.

Another "structural use" for PCB's , in addition to your excellent examples:. Make up some rails to use to hold cut tape on the PnP machine,

Interesting.Actually using the word "rail"  makes me think of some of the unusual things I have used DIN rail for. Maybe there is another blog in that.

 

salbayeng
User Rank
Author
DIN rail modules as an art form!
salbayeng   11/20/2013 11:07:36 PM
NO RATINGS
Hi Aubrey,

These are brilliant ! .

Another neat module on DIN rail I've seen is the current sensor, It's just a current transformer and relay on the PCB, the actual current carrying wire just goes through the hole in the CT without touching the PCB.

Where do you get the DK5 and DK6 housings from ? (fig11 & 12), they seem really hard to get hold of , I have about 20 x DK5 but can't seem to get any more. (There is apparently a thicker version of the DK5 too.)

I love figure 9 ! , just yesterday I completed a (DIN rail mounted annunciator) PCB for a client that has only 9 leds and is 7" x 3" (It's a copy of an existing PCB they have) your approach is much more elegant.

Figure 8 is agreat way to use up all that spare real estate on a pcb panel. But you need the right brand of fuseholder, a quick look in my box of DIN bits shows it won't work on any of the fuesholders I have :<( but you have inspired for something else I can do with them.

=============== using the wasted rails on PCB panels ==========

Another "structural use" for PCB's , in addition to your excellent examples:. Make up some rails to use to hold cut tape on the PnP machine, (I've just included some on my most recent PCB panel) , does something useful with all the wasted rails on top and bottom, You can hold about 15-20 strips each ~ 100 smt parts in 8,12,16,24mm tape , (when you push the tape onto the 1.55mm pins, the tape stays put as the sprocket holes are 1.50mm) :

You make up a set of rails like a picket fence, the top and bottom rails just have 2.7mm holes , spaced at 4mm pitch , I make them 0.300" wide but it's not critical. Like this Ascii art:

______________________________________________________-

O    O O    O O    O O    O O      O      <-2.8mm @ n x 4mm
______________________________________________________

The "pickets" are 7.5mm wide , and have some small holes on 4mm pitch, 1.25mm in from right edge (solder some 1.55mm diam millmax type pins in these later) , and also 2.7mm holes at top and bottom, positioned 5.0mm from right edge. make them a bit more than 400mm long (=100 parts on typical tape) Like this:

_________________________________________________________

         o o                   o o                            o o <-1.60 holes at 4mm

O                                                                  O <- 2.7 at each end

_________________________________________________________

_

Stephen_M
User Rank
Author
Re: Safety?
Stephen_M   11/20/2013 8:20:32 PM
NO RATINGS
Most excellent.

After I posted I realized that I intended to post to "4 Shocking High-Voltage Projects With Arduino". Those look far less robust for working with line voltages.

Sorry for the inconvenience.

 

antedeluvian
User Rank
Author
Re: Safety?
antedeluvian   11/20/2013 8:11:55 PM
NO RATINGS
Stephen_M

All of this stuff looks like enthusiasts/hobbists level manufacturing and it isn't clear if any of this has any kind of Nationally Recognized Test Laboratory markings.

Where required, and where the product is released for production (some of the stuff shown only made it to the prototype phase) the product has been approved and carries the necessary CSA and UL markings.

I put together the photos from stuff hanging around the lab, so it is mostly prototypes or stripped down to show the PCB without all the packaging around it.

Stephen_M
User Rank
Author
Safety?
Stephen_M   11/20/2013 7:53:29 PM
NO RATINGS
Posted to wrong topic. Comment retracted by author.

Max The Magnificent
User Rank
Author
Re: FR4 PCB is water proof
Max The Magnificent   11/19/2013 4:26:22 PM
NO RATINGS
@dougwithau: ...We put in a rubber gasket, made the board double thickness, and screwed it into the enclosure. It was a connector on each side, and ground plain to the screws...

Very cool -- any chance of a photo? (max.maxfield@ubm.com)

Page 1 / 2   >   >>


Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Radio
NEXT UPCOMING BROADCAST

What are the engineering and design challenges in creating successful IoT devices? These devices are usually small, resource-constrained electronics designed to sense, collect, send, and/or interpret data. Some of the devices need to be smart enough to act upon data in real time, 24/7. Are the design challenges the same as with embedded systems, but with a little developer- and IT-skills added in? What do engineers need to know? Rick Merritt talks with two experts about the tools and best options for designing IoT devices in 2016. Specifically the guests will discuss sensors, security, and lessons from IoT deployments.
Like Us on Facebook
Special Video Section
Linear Technology’s LT8330 and LT8331, two Low Quiescent ...
The quality and reliability of Mill-Max's two-piece ...
01:34
The quality and reliability of Mill-Max's two-piece ...
LED lighting is an important feature in today’s and future ...
05:27
The LT8602 has two high voltage buck regulators with an ...
05:18
Silego Technology’s highly versatile Mixed-signal GreenPAK ...
The quality and reliability of Mill-Max's two-piece ...
01:34
Why the multicopter? It has every thing in it. 58 of ...
Security is important in all parts of the IoT chain, ...
Infineon explains their philosophy and why the multicopter ...
The LTC4282 Hot SwapTM controller allows a board to be ...
This video highlights the Zynq® UltraScale+™ MPSoC, and sho...
Homeowners may soon be able to store the energy generated ...
The LTC®6363 is a low power, low noise, fully differential ...
See the Virtex® UltraScale+™ FPGA with 32.75G backplane ...
Vincent Ching, applications engineer at Avago Technologies, ...
The LT®6375 is a unity-gain difference amplifier which ...
The LTC®4015 is a complete synchronous buck controller/ ...
10:35
The LTC®2983 measures a wide variety of temperature sensors ...
The LTC®3886 is a dual PolyPhase DC/DC synchronous ...