Breaking News
Newest First | Oldest First | Threaded View
User Rank
transient protection
cookiejar   11/27/2013 6:54:42 PM
Don't forget to have some form of transient protection for the energy burst you'll get from a nearby lightning strike.


If you're near enough to a high voltage hydro line you can light up as many florescent bulbs as you want without any circuitry whatsoever. With a little ingenuity you could power your whole house.  But that would be stealing hydro power.

User Rank
Re: Messing with values
Bert22306   11/27/2013 6:06:19 PM
Actually, doing the numbers shows how even being relatively close to a very high power TV transmitter won't give you much energy harvesting potential at all. Unless you can build a spherical antenna around the tower, I suppose.

UHF Digital TV in the US is limited by the FCC to a max of 1 MW of effective radiated power. So, let's say you're in the beam of a 600 MHz transmitter, a mere 1 mile away, with a unity gain antenna. How much power can you dream to harvest from that 1 MW signal, with a circuit tuned to 600 MHz?

At 1 mile, with direct line of sight, channel loss is 92.15 dB. So the maximum theoretical amount of power you can harvest, with this unity gain receive antenna, is a mere 0.6 mW. Increase the distance to 1.5 miles, and you're getting to nothing much useful harvested, for powering devices.

User Rank
Re: Messing with values
DU00000001   11/26/2013 3:11:26 PM
Not to forget: this is a tuned circuit !

Probably the biggest problem when thinking about 'harvesting' wireless (or acoustic - it's just the same problem) energy:
there are a lot of frequencies. To harvest you have to rectify at some point and the mean amplitude of the superposed frequencies tends to be 0 :(

Another thought: harvesting acoustic energy would be really great. Currently we've got noise protection embankments here (Germany, Europe) but noise reduction by energy harvesting would be really great. But the problems stay: tuning and mean amplitude.

User Rank
Re: Messing with values
Bill_Jaffa   11/26/2013 2:43:14 PM
Good analysis, thanks.


The thing I like about using RF is that there is so much around, from broadcast etc that is truly "wasted". The thing I don't like is that it is a very weak source despite its pervasiveness, as you point out. And as another commenter pointed out, if you are not careful, the random field you absorb may be the energy that someone else's handset or similarr needed to see, so they are unfortunately blocked.

The old story: there are no free lunches due to the laws of physics, but some lunches are less expensive that others or cause less indigestion.


User Rank
Messing with values
DU00000001   11/26/2013 2:27:06 PM
I did a cursory review of the APL paper. These guys surely do not revolutionize physics and there is no real need to worry about WiFi network performance. To clarify things I'll give what I've found:

1. The 7.3 Volts are OC. Thus power is 0 at that point.
2. They fed 24.25 dBm (ca. 266 mW) into a waveguide, thus
    loosing no significant amount of the power fed.
3. Assuming that the optimum load resistance of ca. 70 R has
    anything to do with 100 mA current is not their fault.
    BTW: the picture shows a green LED shining not too bright.
    That would be more like .. 10 mA @ 2.4 V -> 24 mW.
4. They state a conversion efficiency of ca. 14.2 % for a single
    cell and 36.8 % for a 5x1 array. That's surely not bad for
    coreless wireless transmission, but think about what a
    transformer design could have achieved.
5. Luckily they did an experiment: the simulation gave them
    an efficiency of twice the values they could confirm by
    That's how myths are born :)

Anyway, I hope they had fun.

Dreaming of powering sensors that way ? Stick to the µW of power consumption as you would not want to supply a field of 2 mW/cm².

Some Guy
User Rank
This will shine for ubiquitous sensors
Some Guy   11/26/2013 12:40:02 PM
The place that this technology will shine is for ubiquitous sensors. I've seen proof-of-concept sensor applications using such an approach. It puts remote sensors (strain gages) on bridges to safegard against events like the collapse of the I-35 bridge across the Mississippi River in Minneapolis a few years ago. This obviates the issue of how you distribute power to all the sensors, provides the wireless comms and likely leads to SoCs for the Internet of Things that have inherent power supplies. Imagine smoke detectors that never need new batteries! Thermostats in every room of your house and zone control by room not tied to where they put the LV wires when it was built.

Charles J Gervasi
User Rank
Re: Voltage is a common issue with harvesting.
Charles J Gervasi   11/26/2013 12:07:14 PM
" It will likely produce a dropout of the field in the immediate area of the device. Widespread use of these absorbent resonators could make the wifi non functional for some users.  "

That would be amazing, but I'm sure that's not true.  In a typical communications link budget, 10dBm is delivered to the transmitting antenna.  The signal is radiated in all directions.  A good antenna across the room will be lucky to capture -40dBm (i.e. ten millionths of the transmitted power).  It will follow the free-space loss equation.  You can get more if the receiving antenna is in the near-field (less than 5 inches for wifi).  But the notion that a receiving antenna is going to suck all the power and deliver it to the receiver is wrong.  That would be an amazing thing for the communications industry.

To me the application for this is to direct a "safe" level of RF energy at the device that needs power.  You direct maybe one watt to it and hope to recover a milliwatt.  The rest of the power goes to heating up water molecules.  Kooks currently complain that 100mW transmitters cause health problems.  Wait until we're intentionally causing 1W to couple people's dinner tables to power tablets and phones. 

User Rank
Laws of Physics
ehexpert   11/26/2013 7:42:14 AM
I fear this another device attempting to defy the laws of physics or endanger human life.

Would the researchers please say if they would be prepared to stand next to the harvester for a specified period while it generates 700mW of power (0.1Ax0.1A x 70 Ohms). It is worth looking at this de bunk of an earlier device, Airnergy. Nokia also retracted an announcement made through MIT for a mobile phone charging device using ambient RF Energy. 

User Rank
prabhakar_deosthali   11/26/2013 6:43:10 AM
Though currently it seems something that has no practicality I see many areas where such technique could produce a considerable amount of power ( sufficient current at sufficient voltage ).

For examples those shield used in our domestic microwave oven could use such techniques to transform all that wasted radiation in some useful energy !

Charles J Gervasi
User Rank
Voltage is a common issue with harvesting.
Charles J Gervasi   11/25/2013 8:54:54 PM
I went to a presentation on nanofiber engergy harvesting, and had the same issue.  How do you get that power out if the voltage is in the mW.  That's outside their scope of research.  

These guys got 7V.  7V into a 70 ohm load is amazing!  I wonder if they had this thing in an RF field strong enough to burn your skin. Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)

What are the engineering and design challenges in creating successful IoT devices? These devices are usually small, resource-constrained electronics designed to sense, collect, send, and/or interpret data. Some of the devices need to be smart enough to act upon data in real time, 24/7. Are the design challenges the same as with embedded systems, but with a little developer- and IT-skills added in? What do engineers need to know? Rick Merritt talks with two experts about the tools and best options for designing IoT devices in 2016. Specifically the guests will discuss sensors, security, and lessons from IoT deployments.
Like Us on Facebook
Special Video Section
LED lighting is an important feature in today’s and future ...
The LT8602 has two high voltage buck regulators with an ...
The quality and reliability of Mill-Max's two-piece ...
Why the multicopter? It has every thing in it. 58 of ...
Security is important in all parts of the IoT chain, ...
Infineon explains their philosophy and why the multicopter ...
The LTC4282 Hot SwapTM controller allows a board to be ...
This video highlights the Zynq® UltraScale+™ MPSoC, and sho...
Homeowners may soon be able to store the energy generated ...
The LTC®6363 is a low power, low noise, fully differential ...
See the Virtex® UltraScale+™ FPGA with 32.75G backplane ...
Vincent Ching, applications engineer at Avago Technologies, ...
The LT®6375 is a unity-gain difference amplifier which ...
The LTC®4015 is a complete synchronous buck controller/ ...
The LTC®2983 measures a wide variety of temperature sensors ...
The LTC®3886 is a dual PolyPhase DC/DC synchronous ...
The LTC®2348-18 is an 18-bit, low noise 8-channel ...
The LT®3042 is a high performance low dropout linear ...