Embedded Systems Conference
Breaking News
Comments
Newest First | Oldest First | Threaded View
<<   <   Page 4 / 6   >   >>
Max The Magnificent
User Rank
Author
Re: How would you judge?
Max The Magnificent   11/27/2013 12:27:04 PM
NO RATINGS
@Antedeluvian: ... I have no illusions about winning!

That's good to hear, because I plan on entering also :-)

Max The Magnificent
User Rank
Author
Re: How would you judge?
Max The Magnificent   11/27/2013 12:26:02 PM
NO RATINGS
@Antedelivian: How would you judge the solder joins? neatness, connectivity, symmetry, strength, "blobiness"?

Well, this is something we would have to decide beforehand.

Max The Magnificent
User Rank
Author
Re: Getting nasty
Max The Magnificent   11/27/2013 12:24:37 PM
NO RATINGS
@Antedeluvian: If you want to separate the wheat from the chaff, try getting them to solder magnet wire.

Ooohhhhhh, you are a cruel man!

 

Max The Magnificent
User Rank
Author
Re: Soldering challange
Max The Magnificent   11/27/2013 12:23:41 PM
NO RATINGS
@SteveDS: To make it really interesting you need to dead bug a chip on the board with blue wires!


Good idea -- if we do go ahead with this, maybe we should form a group to come up with a special competition board and associated tasks.

Crusty1
User Rank
Author
Re: I remember it well
Crusty1   11/27/2013 6:55:44 AM
NO RATINGS
@David: I think my first head of department at London Underground Research Labs showed me how to do it and it mainly concerned getting the oxide coat off with fairly normal lab reagents, and then quickly soldering.

@Max; While thinking about a soldering competetion you could make life interesting by getting the contestants to measure the resistance using a slide wire potentiometer and Weston Cell. How many have used similar old kit?

I used, once, a Cambridge optical pyrometer at college, but I have never seen another one to put my hands on.

 

David Ashton
User Rank
Author
Re: I remember it well
David Ashton   11/27/2013 4:50:42 AM
NO RATINGS
@Crusty....Manganin.... can't help you there....nor can google, much.... some suggestions on iron temperature and usng a special flux?

Crusty1
User Rank
Author
Re: I remember it well
Crusty1   11/27/2013 4:35:03 AM
NO RATINGS
@David: Oh how I had forgotton those horrible tinsel wires. All my headphones were government surplus from a shop called Job Stocks.

Manganin resistance wire needed a trick which I seem to have forgotten?

David Ashton
User Rank
Author
Re: I remember it well
David Ashton   11/27/2013 4:17:50 AM
NO RATINGS
@Crusty....working on military radios I had similar problems with the "Tinsel" wires used in handset and microphone curly cords.  The trick was to get a strand out of multistranded wire, and use it to bind up the tinsel cores.  You could do a very neat job with practice.

David Ashton
User Rank
Author
Re: How would you judge?
David Ashton   11/27/2013 4:14:29 AM
NO RATINGS
@Max - I reckon Duane would be a good judge for your competition?

Crusty1
User Rank
Author
Re: I remember it well
Crusty1   11/27/2013 3:52:35 AM
NO RATINGS
Soldering with the 300 watt had soldering iron was a real pain at 10 years old the Iron was so heavy to hold.

Multi strand Litz wire tails from a tuning coil were the killer of dry joints for me, until dad showed me the trick of soldering it. Dip the cotton and shelac coated wires in alcohol, set light to the end and wait for a lovely bright glob of copper to form and then blow the flame out and then solder. Oh what lovely mini fires I had with this.

It seems to me basic soldering skills are something that needs to be taught on the bench, preferably in a flame proof room.

<<   <   Page 4 / 6   >   >>


Radio
LATEST ARCHIVED BROADCAST
As data rates begin to move beyond 25 Gbps channels, new problems arise. Getting to 50 Gbps channels might not be possible with the traditional NRZ (2-level) signaling. PAM4 lets data rates double with only a small increase in channel bandwidth by sending two bits per symbol. But, it brings new measurement and analysis problems. Signal integrity sage Ransom Stephens will explain how PAM4 differs from NRZ and what to expect in design, measurement, and signal analysis.

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Like Us on Facebook
Special Video Section
The LTC®6363 is a low power, low noise, fully differential ...
Vincent Ching, applications engineer at Avago Technologies, ...
The LT®6375 is a unity-gain difference amplifier which ...
The LTC®4015 is a complete synchronous buck controller/ ...
10:35
The LTC®2983 measures a wide variety of temperature sensors ...
The LTC®3886 is a dual PolyPhase DC/DC synchronous ...
The LTC®2348-18 is an 18-bit, low noise 8-channel ...
The LT®3042 is a high performance low dropout linear ...
Chwan-Jye Foo (C.J Foo), product marketing manager for ...
The LT®3752/LT3752-1 are current mode PWM controllers ...
LED lighting is an important feature in today’s and future ...
Active balancing of series connected battery stacks exists ...
After a four-year absence, Infineon returns to Mobile World ...
A laptop’s 65-watt adapter can be made 6 times smaller and ...
An industry network should have device and data security at ...
The LTC2975 is a four-channel PMBus Power System Manager ...
In this video, a new high speed CMOS output comparator ...
The LT8640 is a 42V, 5A synchronous step-down regulator ...
The LTC2000 high-speed DAC has low noise and excellent ...
How do you protect the load and ensure output continues to ...