Breaking News
Comments
Newest First | Oldest First | Threaded View
Page 1 / 4   >   >>
biassetting
User Rank
Rookie
Anyone have the coil data for this Gd-1A??
biassetting   3/25/2014 2:36:35 AM
NO RATINGS
I have been looking for any coil data that I could build replacement coils from. If anyone has the coil data and and a suitible diode replacement for the rectifier I most certain lt would appreciate the help.  Thanks

grover_gren
User Rank
Rookie
Re: Grid dip Meter
grover_gren   12/10/2013 9:17:47 AM
NO RATINGS
thanks for that comment mhrackin. D'Arsonval was an interesting chap, and what a time to work in science (1851 - 1940)

mhrackin
User Rank
CEO
Re: Grid dip Meter
mhrackin   12/9/2013 3:26:00 PM
NO RATINGS
Believe it or not, back in the '50s the "electrician's knot" was the CODE REQUIREMENT for power cord strain relief! Usually used with a rubber (natural of course) grommet that prvided a cushion between the CLOTH insulation and the nasty sharp edges of the hole in the sheet metal.  While on the topic of ancient history, the moving-coil meter movement had a name (eponymous with the inventor): D'Arsonval.  I still have quite a few Bakelite "terminal strips" for the RIGHT way to do the point-to-point wiring; flying connections were amateurish (no slur on hams, BTW; I've been licensed since 1957, ARRL Life Member).  Also ground lugs, along with some military-grade insulated standoffs for the same purpose as the strips (but single-point with a turret top compared to the multi-point terminal strips).  Despite the relative fragility of the vacuum tubes, the rest of the typical constructions of that era were pretty rugged, as they had to be with several hundred volts and high currents everywhere.

grover_gren
User Rank
Rookie
Re: Grid dip Meter
grover_gren   12/2/2013 10:00:39 AM
NO RATINGS
Well done mister C you have found another monster! A truly scary-looking lump of hardware that deserves to be torn down and buried in ten different places. It looks like something reclaimed from the chamber at Abu Ghraib. Did I spot a half-hitch tied in the mains cable to provide strain relief? Nasty nasty. KILL IT WITH THE BIG HAMMER!  

Jerrysc
User Rank
Manager
Grid dip Meter
Jerrysc   12/1/2013 11:17:48 AM
NO RATINGS
Mine was a slightly later tube model. Looked the same except the meter bezel was transparent. Pulled it out after many years of storage and it was still in working order. Dont really have a use for it anymore so I sold it on eBay for $25.

David Ashton
User Rank
Blogger
Re: More on the Dip Meter...
David Ashton   12/1/2013 3:57:57 AM
NO RATINGS
@Sanjib....if you want to be brave (and have fun) and make one yourself there is what looks like a very nice design here

http://sm0vpo.com/use/gdo.htm

80 KHz to 460 MHz - covers a good range.  I have not yet built one but it is on my to-do list....

Sanjib.A
User Rank
CEO
Re: More on the Dip Meter...
Sanjib.A   12/1/2013 12:15:45 AM
NO RATINGS
Okay...thanks a lot!

xwindowsjunkie
User Rank
Rookie
Wait a minute!
xwindowsjunkie   11/30/2013 3:23:30 PM
NO RATINGS
I'm still using mine. It's not an antique, because if it is then I'm...........


Yes I built mine. It was the second Heathkit I built. It still has the original 6AF4 in it but the selenium rectifier has been replaced with a silicon diode and the power filter cap as well. 

I remember seeing a few articles way back then that had conversions detailed to put JFETs in place of the triode. One even went so far as to replace the power transformer with a basic 12.6/6.3 filament transformer so you could eliminate the high voltage (at least on the secondary side).

w2aew
User Rank
Rookie
Re: More on the Dip Meter...
w2aew   11/30/2013 2:22:48 PM
NO RATINGS
There are probably not many being made these days. But MFJ Enterprises is still selling one http://www.mfjenterprises.com/Product.php?productid=MFJ-201

Jonathan Allen
User Rank
Rookie
Grid dip meter
Jonathan Allen   11/30/2013 1:26:18 PM
NO RATINGS
For anyone who wantsa to learn more about the grid dip meter, let me recommend a book:  "Servicing with Dip Meters" by John D. Lenk.  Howard W. Sams Co, 1968.


The Radio Amateur's Handbook also discusses this versatile instrument. 

 

 

Page 1 / 4   >   >>


EE Life
Frankenstein's Fix, Teardowns, Sideshows, Design Contests, Reader Content & More
Max Maxfield

How to Fly Without Catching the Dreaded Lurgy?
Max Maxfield
19 comments
I am currently not wearing my happy face. In fact, I am a "poorly soldier," as my mother would say when I was a little lad.

EDN Staff

11 Summer Vacation Spots for Engineers
EDN Staff
19 comments
This collection of places from technology history, museums, and modern marvels is a roadmap for an engineering adventure that will take you around the world. Here are just a few spots ...

Glen Chenier

Engineers Solve Analog/Digital Problem, Invent Creative Expletives
Glen Chenier
15 comments
- An analog engineer and a digital engineer join forces, use their respective skills, and pull a few bunnies out of a hat to troubleshoot a system with which they are completely ...

Larry Desjardin

Engineers Should Study Finance: 5 Reasons Why
Larry Desjardin
45 comments
I'm a big proponent of engineers learning financial basics. Why? Because engineers are making decisions all the time, in multiple ways. Having a good financial understanding guides these ...

Flash Poll
Top Comments of the Week
Like Us on Facebook
EE Times on Twitter
EE Times Twitter Feed

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)