Breaking News
Comments
Newest First | Oldest First | Threaded View
ROV ENG
User Rank
Rookie
Instrumented Fasteners
ROV ENG   12/1/2013 11:15:13 AM
NO RATINGS
It's not difficult to put a strain gauge into the center of fasteners as small as 1/4" in diameter, we were doing this in the early 80's using proprietary techniques. The sensors were sealed inside the fastener and were suitable for use underwater. The two issues that limited widespread use were the cost and the reduction in strength of the fastener for smaller sizes. This only works for bolted fasteners unless you have a very well defined parting line between the two joined structural elements, which is where the sensor must be located. Accuracies of 0.1% were routinely achieved. Most customers were not so interested in measuring the tension in the fastener during installation, although that was useful information, they were more interested in measuring forces during operation of the machine.

Per ASME B18.2.1, a bolt is designed to be inserted through a hole and secured with a nut, while a screw is designed to be used in a threaded hole—sometimes along with a nut.

RJHonders
User Rank
Rookie
Re: reliability?
RJHonders   11/29/2013 4:59:44 PM
NO RATINGS
CookieJar, you hit the nail on the head. Hard to put sensors in small screws and get the signals out.

vapats
User Rank
Rookie
Re: torque
vapats   11/28/2013 8:39:39 PM
NO RATINGS
Torque is not a proper measure of screw/bolt tension;  you must measure the actual elongation (stretch) of the fastener.


Torque is a mere (and often highly inaccurate) approximation.

 

prabhakar_deosthali
User Rank
CEO
Re:
prabhakar_deosthali   11/28/2013 6:50:02 AM
NO RATINGS
To ascertain that the screws are not overstressed while tightening them,  one can use the torque screw drivers where you can set the maximum torque that will be applied to the screw while it is tightened.

That will eliminated the possibility of the built-in sensor getting damaged by the screw tightening action.

vvc0
User Rank
Manager
Re: reliability?
vvc0   11/27/2013 6:07:51 PM
NO RATINGS
Hmmm, many bolts don't have nuts, such as lag bolts (self tapping), and head bolts (inserted into a tapped hole in an engine head), to name a couple. Also, screws can have nuts, such as machine screws, and even sheet metal screws with tinnerman nuts. The differentiation is more based on the diameter than the fact it is used with/without a nut, but even this is somewhat nebulous.

Stephen_M
User Rank
Freelancer
Re: reliability?
Stephen_M   11/27/2013 2:35:11 PM
NO RATINGS
A bolt is used with a nut to hold things together. A screw can be used without a nut; ex: sheet metal and wood screws, self tapping, self drilling screws.

cookiejar
User Rank
CEO
reliability?
cookiejar   11/27/2013 12:48:47 PM
I assume the idea is to locate a load cell in the tip of a screw to measure force. 

Having worked with load cells, I found the major design challenge using load cells was to keep them from being overloaded and going into plastic deformation.  Just the thought of a applying a tightening torque to a screw makes me cringe as that would twist the delicate load cell structure.  If you build in a mechanism to stop rotation between the two ends of the load cell, the stop friction will affect your readings. 

Trying to do all this in the extremely limited room at the end of a screw would be a challenge as I've always thought of screws being less than 1/4" in diameter and bolts being 1/4" and larger.  But I suppose that may have been lost in translation.




Most Recent Comments
sprite0022
 
Sheepdoll
 
DMcCunney
 
alex_m1
 
Wnderer
 
betajet
 
betajet
 
DMcCunney
 
betajet
EE Life
Frankenstein's Fix, Teardowns, Sideshows, Design Contests, Reader Content & More
Max Maxfield

Some Days You're the Pigeon, Others You're the Statue
Max Maxfield
5 comments
I was watching the travel channel on television the other evening. It was some program about Madrid. The thing I really noticed was the plethora of statues all over the place.

EDN Staff

11 Summer Vacation Spots for Engineers
EDN Staff
20 comments
This collection of places from technology history, museums, and modern marvels is a roadmap for an engineering adventure that will take you around the world. Here are just a few spots ...

Glen Chenier

Engineers Solve Analog/Digital Problem, Invent Creative Expletives
Glen Chenier
15 comments
- An analog engineer and a digital engineer join forces, use their respective skills, and pull a few bunnies out of a hat to troubleshoot a system with which they are completely ...

Larry Desjardin

Engineers Should Study Finance: 5 Reasons Why
Larry Desjardin
46 comments
I'm a big proponent of engineers learning financial basics. Why? Because engineers are making decisions all the time, in multiple ways. Having a good financial understanding guides these ...

Flash Poll
Top Comments of the Week
Like Us on Facebook
EE Times on Twitter
EE Times Twitter Feed

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)