Breaking News
Newest First | Oldest First | Threaded View
User Rank
Instrumented Fasteners
ROV ENG   12/1/2013 11:15:13 AM
It's not difficult to put a strain gauge into the center of fasteners as small as 1/4" in diameter, we were doing this in the early 80's using proprietary techniques. The sensors were sealed inside the fastener and were suitable for use underwater. The two issues that limited widespread use were the cost and the reduction in strength of the fastener for smaller sizes. This only works for bolted fasteners unless you have a very well defined parting line between the two joined structural elements, which is where the sensor must be located. Accuracies of 0.1% were routinely achieved. Most customers were not so interested in measuring the tension in the fastener during installation, although that was useful information, they were more interested in measuring forces during operation of the machine.

Per ASME B18.2.1, a bolt is designed to be inserted through a hole and secured with a nut, while a screw is designed to be used in a threaded hole—sometimes along with a nut.

User Rank
Re: reliability?
RJHonders   11/29/2013 4:59:44 PM
CookieJar, you hit the nail on the head. Hard to put sensors in small screws and get the signals out.

User Rank
Re: torque
vapats   11/28/2013 8:39:39 PM
Torque is not a proper measure of screw/bolt tension;  you must measure the actual elongation (stretch) of the fastener.

Torque is a mere (and often highly inaccurate) approximation.


User Rank
prabhakar_deosthali   11/28/2013 6:50:02 AM
To ascertain that the screws are not overstressed while tightening them,  one can use the torque screw drivers where you can set the maximum torque that will be applied to the screw while it is tightened.

That will eliminated the possibility of the built-in sensor getting damaged by the screw tightening action.

User Rank
Re: reliability?
vvc0   11/27/2013 6:07:51 PM
Hmmm, many bolts don't have nuts, such as lag bolts (self tapping), and head bolts (inserted into a tapped hole in an engine head), to name a couple. Also, screws can have nuts, such as machine screws, and even sheet metal screws with tinnerman nuts. The differentiation is more based on the diameter than the fact it is used with/without a nut, but even this is somewhat nebulous.

User Rank
Re: reliability?
Stephen_M   11/27/2013 2:35:11 PM
A bolt is used with a nut to hold things together. A screw can be used without a nut; ex: sheet metal and wood screws, self tapping, self drilling screws.

User Rank
cookiejar   11/27/2013 12:48:47 PM
I assume the idea is to locate a load cell in the tip of a screw to measure force. 

Having worked with load cells, I found the major design challenge using load cells was to keep them from being overloaded and going into plastic deformation.  Just the thought of a applying a tightening torque to a screw makes me cringe as that would twist the delicate load cell structure.  If you build in a mechanism to stop rotation between the two ends of the load cell, the stop friction will affect your readings. 

Trying to do all this in the extremely limited room at the end of a screw would be a challenge as I've always thought of screws being less than 1/4" in diameter and bolts being 1/4" and larger.  But I suppose that may have been lost in translation. Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)

What are the engineering and design challenges in creating successful IoT devices? These devices are usually small, resource-constrained electronics designed to sense, collect, send, and/or interpret data. Some of the devices need to be smart enough to act upon data in real time, 24/7. Specifically the guests will discuss sensors, security, and lessons from IoT deployments.

Brought to you by:

Like Us on Facebook
Special Video Section
Power can be a gating factor in success or failure of ...
Get to market faster and connect your next product to the ...
See how microQSFP is setting a new standard for tomorrow’s ...
The LTC3649 step-down regulator combines key features of a ...
Once the base layer of a design has been taped out, making ...
In this short video we show an LED light demo to ...
The LTC2380-24 is a versatile 24-bit SAR ADC that combines ...
In this short video we show an LED light demo to ...
Wireless Power enables applications where it is difficult ...
LEDs are being used in current luxury model automotive ...
With design sizes expected to increase by 5X through 2020, ...
Linear Technology’s LT8330 and LT8331, two Low Quiescent ...
The quality and reliability of Mill-Max's two-piece ...
LED lighting is an important feature in today’s and future ...
The LT8602 has two high voltage buck regulators with an ...
Silego Technology’s highly versatile Mixed-signal GreenPAK ...
The quality and reliability of Mill-Max's two-piece ...
Why the multicopter? It has every thing in it. 58 of ...
Security is important in all parts of the IoT chain, ...
Infineon explains their philosophy and why the multicopter ...