Breaking News
Comments
Newest First | Oldest First | Threaded View
MeasurementBlues
User Rank
Blogger
Rise time of digital signals
MeasurementBlues   1/1/2014 12:58:38 PM
NO RATINGS
Adam,

I usually think of decoupling caps in relation to digital devices. Can you relate wavelength to the rise time of a digital signal? That will help in understanding both the value of a decoupling cap and the distance from the IC that needs power supplied by the cap.

MeasurementBlues
User Rank
Blogger
Re: Choosing smaller Decoupling capacitor packages
MeasurementBlues   1/1/2014 12:51:32 PM
NO RATINGS
@Sanjib, that's the general thinking, redce loops wherever possible and you reduce EMI emissions and susceptibility problems. There's also the inductance of the capacitor itself, depending on the frequencies in your circuit.

Sanjib.A
User Rank
CEO
Choosing smaller Decoupling capacitor packages
Sanjib.A   12/21/2013 5:45:57 AM
NO RATINGS

Is there an advantage of using smaller decoupling capacitor packages e.g. 0402 over the bigger packages such as 0805 from signal/power integrity, EMI stand point? Obviously the important electrical parameters such as voltage, capacitance shall meet requirement first. But I was thinking if smaller sizes would reducing the loop & inductance even further, and hence should be the first priority from EMI point of view, apart from the fact that these take lesser space.

er.vikasjha
User Rank
Rookie
Re: Bipolar supplies
er.vikasjha   12/20/2013 12:25:38 AM
NO RATINGS
My experience is better to use Decoupling Cap NW wrt FB as during EMC , Ferrites behavior relatively to Parasitic Impedance is Unpredictable

 

salbayeng
User Rank
Rookie
Via placement and FB's
salbayeng   12/18/2013 5:55:27 PM
NO RATINGS
Hi all, 

I try to put pairs of via's either side of the pad where possible, this lowers the effective loop area and makes the "inductor width" wider, both of which reduce inductance. 

And I use ferrite beads wherever possible, a good place for these is on rapidly switching outputs (particularly capacitive loaded ones) this not only prevents ringing , but rounds off the edegs of the circulating currents through VCC and gnd. 

Adam-Taylor
User Rank
Blogger
Re: Isolation Resistors
Adam-Taylor   12/18/2013 3:01:50 PM
NO RATINGS
Sadly a few ohms resistance might cause issues of voltage drop at high currents and complicate the anaylsis of the power distribution network.

If you need to have quieter planes, say for a ADC or DAC then ferrite beads can be used.

 

 

Adam-Taylor
User Rank
Blogger
Re: Bipolar supplies
Adam-Taylor   12/18/2013 2:57:25 PM
NO RATINGS
I would be go with option C as sharing via's increases the inductance and can cause issue if the instantenous demands are large.

This will also increase the inductance due to the tracking required to share the via.

You want to minimise the loop area so treat each supply to ground as its own loop and attempt to minimise it 

I hoope this helps and makes sense

zeeglen
User Rank
Blogger
Isolation Resistors
zeeglen   12/18/2013 2:13:51 PM
NO RATINGS
Any thoughts on the effectiveness of a few ohms resistance between each power pin and its Vdd plane?  This does force the PCB designer into placing a cap close to each pin, but does this confining of the shoot-through current loop to the local capacitor work to keep the planes quieter and reduce radiated EMI?

bk11
User Rank
Manager
Bipolar supplies
bk11   12/18/2013 1:20:00 PM
NO RATINGS
You mention that it is not a good idea to share vias between caps, but what about decoupling devices that use bipolar supplies?  Thre are (at least) three options:

a. One cap from V+ to V-

b. Two caps, each to ground, but sharing a common ground via

c. Two caps with seperate ground vias

I often use option B, with the thought that only the imbalanced current flows through the via, but each supply is decoupled to ground should the imbalance be large.



EE Life
Frankenstein's Fix, Teardowns, Sideshows, Design Contests, Reader Content & More
Max Maxfield

Aging Brass: Cow Poop vs. Horse Doo-Doo
Max Maxfield
41 comments
As you may recall, one of the things I want to do with the brass panels I'm using in my Inamorata Prognostication Engine is to make them look really old. Since everything is being mounted ...

EDN Staff

11 Summer Vacation Spots for Engineers
EDN Staff
18 comments
This collection of places from technology history, museums, and modern marvels is a roadmap for an engineering adventure that will take you around the world. Here are just a few spots ...

Glen Chenier

Engineers Solve Analog/Digital Problem, Invent Creative Expletives
Glen Chenier
13 comments
- An analog engineer and a digital engineer join forces, use their respective skills, and pull a few bunnies out of a hat to troubleshoot a system with which they are completely ...

Larry Desjardin

Engineers Should Study Finance: 5 Reasons Why
Larry Desjardin
45 comments
I'm a big proponent of engineers learning financial basics. Why? Because engineers are making decisions all the time, in multiple ways. Having a good financial understanding guides these ...

Flash Poll
Top Comments of the Week
Like Us on Facebook
EE Times on Twitter
EE Times Twitter Feed

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)