Breaking News
Comments
Newest First | Oldest First | Threaded View
<<   <   Page 2 / 4   >   >>
Max The Magnificent
User Rank
Blogger
Re: Temperature, Humidity, and Pressure
Max The Magnificent   12/29/2013 2:56:23 PM
NO RATINGS
@Robotics Developer: ...it would be most helpful if you had touch bumpers all around to protect your furnature.

I totally agree -- I'm planning on having my robit bristling with sensors of all types, including bump sensors.

Max The Magnificent
User Rank
Blogger
Re: Temperature, Humidity, and Pressure
Max The Magnificent   12/29/2013 2:54:59 PM
NO RATINGS
@Robotics Developr: The other programming feature that would be nice is to increase the polling on the sensors that are closing in on an object to keep from hitting it.

That's a good idea -- thanks for sharing.

Max The Magnificent
User Rank
Blogger
Re: Temperature, Humidity, and Pressure
Max The Magnificent   12/29/2013 2:53:49 PM
NO RATINGS
@Robotics Developer: ...sequencing of the ultra sonics (say left, back, front, right) to prevent echos from interfering...

Agreed -- in fact we are thinking of givng the sensor boards the ability to automatically keep on performing a "round-robin" ping one after the other and to kep on doing it -- whenever the main processor is ready (or interested) it can simply request of any senso "what was your last reading?"

 

Max The Magnificent
User Rank
Blogger
Re: Temperature, Humidity, and Pressure
Max The Magnificent   12/29/2013 2:50:20 PM
NO RATINGS
@Sanjib.A: Btw...why did you chose urtrasound over Infrared? What is the min-max distance directed?


No particular reason -- I was planning on using infraed sensors under the robot to detect edges (like if you put it on a table) -- I've never played with ultrasonics before, so I decided to go that way -- as I recall, they are upposed to be accurate from 2cm to about 450 cm.

 

Sanjib.A
User Rank
CEO
Re: Temperature, Humidity, and Pressure
Sanjib.A   12/29/2013 4:04:27 AM
NO RATINGS
@Max & Duane: Thank you for sharing your project ideas. I was looking for a cheap but fairly accurate ultrasound sensor for a different application (water level measurement of the overhead water tank of my house). I am going to check this out. Btw...why did you chose urtrasound over Infrared? What is the min-max distance directed?

Robotics Developer
User Rank
Rookie
Re: Temperature, Humidity, and Pressure
Robotics Developer   12/28/2013 3:33:32 PM
NO RATINGS
Max, the other thing I would remind you of is the sequencing of the ultra sonics (say left, back, front, right) to prevent echos from interfering.  This is more of an issue with multiple robots in a common environment but the side effect is to reduce the processing overhead to 1 or 2 sensors at a time.  The other programming feature that would be nice is to increase the polling on the sensors that are closing in on an object to keep from hitting it.  All that said, it would be most helpful if you had touch bumpers all around to protect your furnature.

Max The Magnificent
User Rank
Blogger
Re: Temperature, Humidity, and Pressure
Max The Magnificent   12/28/2013 12:06:12 PM
NO RATINGS
@Robitics Developer: Max, regarding the ultrasonics make sure you test out the environment that you want to run them in...

Good point -- also my robot is going to be on its own, but if I were in a robit competition it might be interesting working on "Stealth" technology re ultrasonic and IR sensors on other robots...

Robotics Developer
User Rank
Rookie
Re: Temperature, Humidity, and Pressure
Robotics Developer   12/27/2013 5:19:10 PM
NO RATINGS
Max, regarding the ultrasonics make sure you test out the environment that you want to run them in.  In robotic competitions we "saw" problems with utrasonics and diamond plate.  It seems that with diamond plate the ranging varied greaty due to weird reflections.  Be save and test out the environment..  also could be a nice article to write up for others to learn from your experiences.

 

I did very much enjoy the pun :bouncing back and forth"!! Keep up the puns..

David Ashton
User Rank
Blogger
Re: SR-04 modules
David Ashton   12/20/2013 5:53:28 PM
NO RATINGS
@Max..."I think the on-board electronics on the '04 are just for pulse-shaping/controlling the out-going "ping" and detecting/registering/noise-filtering the incoming response..."

 

From the timing diagram in the datasheet, when you give it an initiate pulse the module will send out 8 40KHz pulses from the transmitter.  Immediately on completion of that it starts the Echo pulse - which it would appear carries on until it detects the end of the echo - that's the pulse you time with your MCU.  

The pulse (by my calculations) is 6.4 CM long....yet the unit can measure down to 2 cm.  I guess working off the trailing edges of the pluses lets it do this.  Quite clever.

Max The Magnificent
User Rank
Blogger
Re: What?
Max The Magnificent   12/20/2013 1:31:50 PM
NO RATINGS
@Duane: It's early. My brain doesn't actually start functioning until about 10:00am out here.

OK, I'll call you back later (LOL)

<<   <   Page 2 / 4   >   >>


EE Life
Frankenstein's Fix, Teardowns, Sideshows, Design Contests, Reader Content & More
Max Maxfield

10 Top Video Parodies on User Interfaces
Max Maxfield
8 comments
As you may know, the people of Scotland are holding a referendum today to decide whether they wish to remain part of the United Kingdom (UK) or to become fully independent and "go it ...

EDN Staff

11 Summer Vacation Spots for Engineers
EDN Staff
20 comments
This collection of places from technology history, museums, and modern marvels is a roadmap for an engineering adventure that will take you around the world. Here are just a few spots ...

Glen Chenier

Engineers Solve Analog/Digital Problem, Invent Creative Expletives
Glen Chenier
15 comments
- An analog engineer and a digital engineer join forces, use their respective skills, and pull a few bunnies out of a hat to troubleshoot a system with which they are completely ...

Larry Desjardin

Engineers Should Study Finance: 5 Reasons Why
Larry Desjardin
46 comments
I'm a big proponent of engineers learning financial basics. Why? Because engineers are making decisions all the time, in multiple ways. Having a good financial understanding guides these ...

Flash Poll
Top Comments of the Week
Like Us on Facebook
EE Times on Twitter
EE Times Twitter Feed

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)