Design Con 2015
Breaking News
Comments
Newest First | Oldest First | Threaded View
David Ashton
User Rank
Blogger
Converting temperature readings
David Ashton   12/20/2013 5:17:38 AM
NO RATINGS
Just a note - in page 1 just above the picture, I said

"I got the FFFF part to display 0.X degrees by dividing it by 25"

I should have added that I had first multiplied it by 16 which gave me a value between 0 and 240 decimal, in steps of 16.  Dividing this by 25 (and ignoring any remainders) gives a value between 0 and 9 which can be used for the digit to the right of the decimal point.   Some values will be one decimal point out compared to the values if you were to round off properly, but with a sensor accuracy of only 0.5 degrees this is not a big deal.

David Ashton
User Rank
Blogger
Re: Measuring temperature
David Ashton   12/19/2013 10:30:48 PM
NO RATINGS
Thanks, Aubrey.  Good points about accuracy and calibration.  I would imagine the DS18B20 is similar to the older DS1820 and certainly ANY heated tracks which can conduct heat to any of the leads will affect the reading somehow.   In my case, the device has an accuracy of +/- 0.5 degree C, which for any purpose I want to use them for is adequate.  This also makes the resolution of 0.0625 degree a bit of overkill in some ways.   That's why I didn't worry too much about rounding errors in my conversion of the fractional part of the temperature to a 0.1 degree resolution for my display.

Compared to Max's thermostat errors (which were in the region of 5 degrees (though that's Fahrenheit, it's about 3 degrees C) the DS18B20 is a very accurate device.  I know what I would use if I were to design an Airconditioning thermostat!

I don't possess any super-accurate temperature calibration devices but obviously when you are using these it's important to have good thermal coupling between the calibration sensor and the DUT.  And you could not do things like put a DS18B20 into an ice bath without insulating it properly, which would probably add some thermal insulation as well.   Fortunately as I said, the basic 0.5 degree accuracy of the DS18B20 is fine for me!

 

 

antedeluvian
User Rank
Blogger
Measuring temperature
antedeluvian   12/19/2013 8:40:11 PM
NO RATINGS
Hi David

Good article, as usual. Something to consider when using this (or any device) is what is actually being measured. Apparently the DS1820 (an obsolete version) measured the temprature of the GND pin- that was how the heat was conducted to the temprature sensor. A TI FAE recently said that this was quite common for solid state temperature sensors.

This came as a rude shock to one of our engineers. He had used the TO92 package up in the breeze to measure the temperature of air floating by. However there were some resistors heating the PCB nearby and it contributed to a measurment error.

Of course that brings us to an issue when it comes to calibrating a temperature sensor- how do you know what is the right temperature, and what exactly is your sensor measuring. Max once did a blog when he faced this problem with his home thermostat: I'm becoming hot and bothered



Top Comments of the Week
Flash Poll
Like Us on Facebook

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
EE Life
Frankenstein's Fix, Teardowns, Sideshows, Design Contests, Reader Content & More
<b><a href=Betajet">

The Circle – The Future's Imperfect in the Present Tense
Betajet
5 comments
The Circle, a satirical, dystopian novel published in 2013 by San Francisco-based writer Dave Eggers, is about a large, very powerful technology company that combines aspects of Google, ...

Max Maxfield

Recommended Reads From the Engineer's Bookshelf
Max Maxfield
27 comments
I'm not sure if I read more than most folks or not, but I do I know that I spend quite a lot of time reading. I hate to be idle, so I always have a book or two somewhere about my person -- ...

Martin Rowe

Make This Engineering Museum a Reality
Martin Rowe
Post a comment
Vincent Valentine is a man on a mission. He wants to make the first house to ever have a telephone into a telephone museum. Without help, it may not happen.

Rich Quinnell

Making the Grade in Industrial Design
Rich Quinnell
16 comments
As every developer knows, there are the paper specifications for a product design, and then there are the real requirements. The paper specs are dry, bland, and rigidly numeric, making ...

Special Video Section
The LT8640 is a 42V, 5A synchronous step-down regulator ...
The LTC2000 high-speed DAC has low noise and excellent ...
How do you protect the load and ensure output continues to ...
General-purpose DACs have applications in instrumentation, ...
Linear Technology demonstrates its latest measurement ...
10:29
Demos from Maxim Integrated at Electronica 2014 show ...
Bosch CEO Stefan Finkbeiner shows off latest combo and ...
STMicroelectronics demoed this simple gesture control ...
Keysight shows you what signals lurk in real-time at 510MHz ...
TE Connectivity's clear-plastic, full-size model car shows ...
Why culture makes Linear Tech a winner.
Recently formed Architects of Modern Power consortium ...
Specially modified Corvette C7 Stingray responds to ex Indy ...
Avago’s ACPL-K30T is the first solid-state driver qualified ...
NXP launches its line of multi-gate, multifunction, ...
Doug Bailey, VP of marketing at Power Integrations, gives a ...
See how to ease software bring-up with DesignWare IP ...
DesignWare IP Prototyping Kits enable fast software ...
This video explores the LT3086, a new member of our LDO+ ...
In today’s modern electronic systems, the need for power ...